September 2014 - App_rpt-users

Multiple requests for registration
by Bob 14 Sep '14

14 Sep '14

My servers are constantly sending registration request and rereqquests. I check two different ones on two different IP addresses at two different locations, although the same ISP. I don't ever remember this happening this much, at this frequency. I'm wondering if there is something I need to fix. Also, is the frequency of these requests adjustable on my end, and is it anything I need to do? The data below is from one server. The other server looks pretty much the same. This one also has Echolink, and I get an Echolink update occasionally interspersed between large groups of the warnings shown below. Thanks, Bob kk6ecm [Sep 12 23:48:34] WARNING[456]: chan_iax2.c:10127 iax2_do_register: REGISTER-LOG: Sending registration request for '29009' [Sep 12 23:48:34] WARNING[459]: chan_iax2.c:7690 registry_rerequest: REGISTER-LOG: registry rereqquest [Sep 12 23:48:44] WARNING[452]: chan_iax2.c:10127 iax2_do_register: REGISTER-LOG: Sending registration request for '28765' [Sep 12 23:48:45] WARNING[454]: chan_iax2.c:7690 registry_rerequest: REGISTER-LOG: registry rereqquest [Sep 12 23:49:24] WARNING[459]: chan_iax2.c:10127 iax2_do_register: REGISTER-LOG: Sending registration request for '29009' [Sep 12 23:49:24] WARNING[458]: chan_iax2.c:7690 registry_rerequest: REGISTER-LOG: registry rereqquest [Sep 12 23:49:35] WARNING[454]: chan_iax2.c:10127 iax2_do_register: REGISTER-LOG: Sending registration request for '28765' [Sep 12 23:49:35] WARNING[456]: chan_iax2.c:7690 registry_rerequest: REGISTER-LOG: registry rereqquest

4 4

Re: [App_rpt-users] rc.updatenodelist fails.
by Bryan Fields 14 Sep '14

14 Sep '14

It appears to be working now. I didn't do anything, so perhaps it aged out or something. Thanks Duuuuude On 9/14/14, 12:20 AM, Bryan Fields wrote: > Ok, good to know. Maybe we can put that in the docs, as it had me fooled > trying to troubleshoot it. > > I'm running it from asterisk.kb9mci.net, 44.98.254.236 which is registered in > the portal for node 40821, and it's still giving an error 403. > > How often does it update the ACL for the server? I've had to move the server > recently. > > Thanks, > > On 9/14/14, 12:14 AM, Jim Duuuude wrote: >> It not going to work unless you attempt access from an IP address that has >> a registered Allstar node. The registration server makes an 'allow list' based upon >> the IP addresses from which you register your Allstar node. > > -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Re: [App_rpt-users] rc.updatenodelist fails.
by Bryan Fields 14 Sep '14

14 Sep '14

Ok, good to know. Maybe we can put that in the docs, as it had me fooled trying to troubleshoot it. I'm running it from asterisk.kb9mci.net, 44.98.254.236 which is registered in the portal for node 40821, and it's still giving an error 403. How often does it update the ACL for the server? I've had to move the server recently. Thanks, On 9/14/14, 12:14 AM, Jim Duuuude wrote: > It not going to work unless you attempt access from an IP address that has > a registered Allstar node. The registration server makes an 'allow list' based upon > the IP addresses from which you register your Allstar node. -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Re: [App_rpt-users] rc.updatenodelist fails.
by Bryan Fields 14 Sep '14

14 Sep '14

Thanks Tim, However, I'm getting 403 errors on each. Perhaps some kinda IP block issue or something? root@KB9MCI:/etc/rc.d# wget http://nodes1.allstarlink.org/cgi-bin/nodes.pl --2014-09-13 23:26:54-- http://nodes1.allstarlink.org/cgi-bin/nodes.pl Resolving nodes1.allstarlink.org... 96.36.57.202 Connecting to nodes1.allstarlink.org|96.36.57.202|:80... connected. HTTP request sent, awaiting response... 403 2014-09-13 23:26:54 ERROR 403: (no description). root@KB9MCI:/etc/rc.d# wget http://nodes2.allstarlink.org/cgi-bin/nodes.pl --2014-09-13 23:27:00-- http://nodes2.allstarlink.org/cgi-bin/nodes.pl Resolving nodes2.allstarlink.org... 209.159.155.200 Connecting to nodes2.allstarlink.org|209.159.155.200|:80... connected. HTTP request sent, awaiting response... 403 Forbidden 2014-09-13 23:27:00 ERROR 403: Forbidden. root@KB9MCI:/etc/rc.d# wget http://nodes3.allstarlink.org/cgi-bin/nodes.pl --2014-09-13 23:27:06-- http://nodes3.allstarlink.org/cgi-bin/nodes.pl Resolving nodes3.allstarlink.org... 65.110.110.172 Connecting to nodes3.allstarlink.org|65.110.110.172|:80... connected. HTTP request sent, awaiting response... 403 2014-09-13 23:27:06 ERROR 403: (no description). root@KB9MCI:/etc/rc.d# wget http://nodes4.allstarlink.org/cgi-bin/nodes.pl --2014-09-13 23:27:11-- http://nodes4.allstarlink.org/cgi-bin/nodes.pl Resolving nodes4.allstarlink.org... 67.214.190.109 Connecting to nodes4.allstarlink.org|67.214.190.109|:80... connected. HTTP request sent, awaiting response... 403 Forbidden 2014-09-13 23:27:12 ERROR 403: Forbidden. On 9/13/14, 11:23 PM, Tim Sawyer wrote: > Works for me… > > > Resolving nodes1.allstarlink.org... 96.36.57.202 > Connecting to nodes1.allstarlink.org|96.36.57.202|:80... connected. > HTTP request sent, awaiting response... 200 OK > Length: unspecified [text/plain] > Saving to: `/var/lib/asterisk/rpt_extnodes-temp' > > [ <=> ] 64,417 225K/s in 0.3s > > 2014-09-13 20:19:36 (225 KB/s) - `/var/lib/asterisk/rpt_extnodes-temp' saved [64417] > > Retrieved node list from nodes1.allstarlink.org > > -- > Tim WD6AWP > >> On Sep 13, 2014, at 8:13 PM, Bryan Fields <Bryan(a)bryanfields.net> wrote: >> >> This is not working, looks like all the servers are not responding. >> >> Problem retrieving node list from nodes1.allstarlink.org, trying another server >> Problem retrieving node list from nodes2.allstarlink.org, trying another server >> Problem retrieving node list from nodes3.allstarlink.org, trying another server >> Problem retrieving node list from nodes4.allstarlink.org, trying another server >> Problem retrieving node list from nodes1.allstarlink.org, trying another server >> >> Ideas? >> >> -- >> Bryan Fields >> >> 727-409-1194 - Voice >> 727-214-2508 - Fax >> http://bryanfields.net >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)ohnosec.org >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. > -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

2 1

rc.updatenodelist fails.
by Bryan Fields 14 Sep '14

14 Sep '14

This is not working, looks like all the servers are not responding. Problem retrieving node list from nodes1.allstarlink.org, trying another server Problem retrieving node list from nodes2.allstarlink.org, trying another server Problem retrieving node list from nodes3.allstarlink.org, trying another server Problem retrieving node list from nodes4.allstarlink.org, trying another server Problem retrieving node list from nodes1.allstarlink.org, trying another server Ideas? -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

2 1

Re: [App_rpt-users] Incoming connects
by wade 13 Sep '14

13 Sep '14

Sorry for the lack of information here. It was late.. lol Ok, I have a slightly different setup here than most but I'm sure some people do it for remote sites. First off my IP here at home is DCHP. I have a friend just down the street running AllStar with the same ISP and he has no issues. (more on his strange solution later). My setup consist of my main router for the house wired to an HSMM Mesh node in my shack. Another Mesh node is setup and wired to the AllStar Server in the garage. (I'm running this as a test to get ready for a remote site without internet.) So my server has an IP that starts with 10.12.xxx.xx. This setup worked flawlessly for months then this. All the routers, including the main house router are LinkSys. I have checked all these mesh nodes and the main router many times and all have the correct ports open. As for SSHíng into it. I can if I am wired into my inside mesh node. I can't from anywhere else, I assume because the nodes are in AD-HOC mode??? Not to familiar woth all the networking SSH stuff quite yet. I will try to capture some data from it but I use a different computer to email from so it is difficult. I hope I didn't leave anyone out of information. Wade On 9/13/2014 7:23 AM, Lu Vencl wrote: > I have had the same problem with one of my nodes out in Colorado. The final outcome turned out to be that century link was blocking the port. You may want to try changing your port number to something else like 14569 and give that a shot. Be sure to change your port forwarding accordingly. > If you like, email me directly with your phone number and I will walk you through it. > > Lu Vencl > KA4EPS > >> On Sep 13, 2014, at 2:45 AM, wade <wadeo(a)charter.net> wrote: >> >> Good evening all, >> >> I have been dealing with an issue for about a month now of nobody being able to connect to me, either from AllStar or Echolink. I can connect to them by radio or using the CLI and it works perfect. Audio is passed back and forth no drops, nothing. But no one can connect in. About 2 weeks ago I was forced to do a complete system reinstall due to a bad streaming install attempt. I thought maybe that would fix my incoming issue also. It did not. I can ping Google and everything is great, no packets dropped. During the course of this investigation I have gone through my router numerous times and the port forwarding is correct, UDP 4569 for AllStar, UDP 5198-5199 and TCP 5200 for Echolink. This setup has worked flawlessly for months after I set it up in it new location then it just quit. >> >> Any ideas that maybe I haven't thought of or maybe something to jar my memory? >> >> >> >> I also have had this message coming across the CLI constantly. >> >> "Warning aprsthread: server noam.aprs2.net cannot be found" >> >> That was a short description as I can not copy and paste it to the computer I use to email from. >> >> I have tried "rotate.aprs.net" and "rotate.aprs2.net" also with no success. >> Could the two issues be related at all? >> >> I would appreciate any help that can be given. I think it is something so basic I am just over looking it and I hope it is. But I wanted to run it past the experts to see if you guys had any other ideas >> >> Thanks >> Wade >> KCØMLT >> Node 28757 >> >> --- >> This email is free from viruses and malware because avast! Antivirus protection is active. >> http://www.avast.com >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)ohnosec.org >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com

1 0

Incoming connects
by wade 13 Sep '14

13 Sep '14

Good evening all, I have been dealing with an issue for about a month now of nobody being able to connect to me, either from AllStar or Echolink. I can connect to them by radio or using the CLI and it works perfect. Audio is passed back and forth no drops, nothing. But no one can connect in. About 2 weeks ago I was forced to do a complete system reinstall due to a bad streaming install attempt. I thought maybe that would fix my incoming issue also. It did not. I can ping Google and everything is great, no packets dropped. During the course of this investigation I have gone through my router numerous times and the port forwarding is correct, UDP 4569 for AllStar, UDP 5198-5199 and TCP 5200 for Echolink. This setup has worked flawlessly for months after I set it up in it new location then it just quit. Any ideas that maybe I haven't thought of or maybe something to jar my memory? I also have had this message coming across the CLI constantly. "Warning aprsthread: server noam.aprs2.net cannot be found" That was a short description as I can not copy and paste it to the computer I use to email from. I have tried "rotate.aprs.net" and "rotate.aprs2.net" also with no success. Could the two issues be related at all? I would appreciate any help that can be given. I think it is something so basic I am just over looking it and I hope it is. But I wanted to run it past the experts to see if you guys had any other ideas Thanks Wade KCØMLT Node 28757 --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com

4 3

Change DTMF autodial Speed
by Skyler F 12 Sep '14

12 Sep '14

I use cop 48 for automatically dialing DTMF sequences in a shell script. in particular: asterisk -rx "rpt cmd 40764 cop 48 x,y" (x, y are my numbers to dial) They are getting annoying at the default speed though, because it automatically dials it on connect and disconnect. and I would really like to speed them up. Is there any way to do this? So instead of DAAHH its more like dit. ? 73 Skyler KDØWHB -- Skyler Fennell amsatnet.info KDØWHB electricity440(a)gmail.com

1 0

What is Dahdi?
by George Csahanin 12 Sep '14

12 Sep '14

OK, not being a wise-ass, not trying to be stupid, that part’s covered. Just trying to understand. What are the specific functions of: Dahdi Asterisk Libpri Zaptel I know they are all part of the whole package, and that whole package still has me in awe. But being very curious type I wanted to know how this all comes together. In my simple mind I axe: why isn’t Asterisk enough? I know what that one is, but as I use app_rpt daily I wish I knew which of the above are providing what part of the overall system. George J Csahanin W2DB Allstar 2360 Echolink-Free Cedar Park, TX 512-401-2630 home 401-338-0568 cel

4 4

Re: [App_rpt-users] What is Dahdi?
by Bryan Fields 12 Sep '14

12 Sep '14

On 9/11/14, 10:39 PM, Doug Crompton wrote: > This will explain it.... > http://blogs.digium.com/2008/05/19/zaptel-project-being-renamed-to-dahdi/ The first comment on that blog post is perfect. -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0