July 2015 - App_rpt-users - lists.keekles.org

Re: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server
by Doug Crompton 03 Jul '15

03 Jul '15

If they are on the same server they should know about each other and you should be able to connect directly internally. Is that not working? 73 Doug WA3DSP http://www.crompton.com/hamradio Subject: Re: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server From: kk6ecm(a)gmail.com Date: Fri, 3 Jul 2015 11:26:00 -0700 To: doug(a)crompton.com Let me re ask my question. Single server with two nodes, no internet; how do I setup app_rpt so the two nodes are always linked (" hard wired", if you will). What is the difference in the *.conf setup for a permanent link between the nodes? I know how to set up the nodes for each radio, just not clear how to link them via the *.conf file setups (e.g. rpt.conf, iax.conf, extensions.conf). Thanks,Bobkk6ecm Sent from iPad On Jul 3, 2015, at 10:47 AM, Doug Crompton <doug(a)crompton.com> wrote: If it is RF connect via radio and it is is wired connect via that. Both will work equally well if the routing is setup properly. No need to have Internet access. 73 Doug WA3DSP http://www.crompton.com/hamradio Subject: Re: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server From: kk6ecm(a)gmail.com Date: Fri, 3 Jul 2015 07:46:21 -0700 CC: app_rpt-users(a)ohnosec.org To: doug(a)crompton.com Two servers connected via an rf link between one node on each server. One server is remote, supporting the rf link and a repeater (no internet), and the second is a normal Allster server with two registered nodes, one connected to a repeater, and the second connected to the radio support its half of the rf link with the other server. Thanks,Bobkk6ecm Sent from iPad On Jul 3, 2015, at 6:18 AM, Doug Crompton <doug(a)crompton.com> wrote: I am assuming these are two separate servers. If so they just have to be on a LAN connected together and the routing has to be setup at each server. They do not have to be registered. In this way they operate as private nodes. Of course anything that needs the Internet will not work. Here is info on doing the routing. It applies equally to any Allstar node - Acid, BBB, RPi2, etc. http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/multi-server%20howt… 73 Doug WA3DSP http://www.crompton.com/hamradio > From: kk6ecm(a)gmail.com > To: app_rpt-users(a)ohnosec.org > Date: Thu, 2 Jul 2015 22:28:17 -0700 > Subject: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server > > I'm looking for information on how to "hardwire" link two nodes together in > my server. One node is full-duplex repeater and the other is a half-duplex > RF link to a second repeater that has full Allstar control on both the > repeater and the link. They are located at a remote site, with no internet > connection after install. I'm sure there are other things I'm missing, but > this will enable me to experiment with final configuration combinations. > > Thanks, > Bob > kk6ecm > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >

1 0

How to Hardwire Two Nodes in One APP_RPT Server
by kk6ecm 03 Jul '15

03 Jul '15

I'm looking for information on how to "hardwire" link two nodes together in my server. One node is full-duplex repeater and the other is a half-duplex RF link to a second repeater that has full Allstar control on both the repeater and the link. They are located at a remote site, with no internet connection after install. I'm sure there are other things I'm missing, but this will enable me to experiment with final configuration combinations. Thanks, Bob kk6ecm

2 3

Is it possible to have two Echolinks on the same server?
by Loren Tedford 03 Jul '15

03 Jul '15

Hi I am trying to figure out how to run two Echolinks on the Same Server can it be done?? If so what does the config look like? Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: http://www.lorentedford.com http://www.kc9zhv.com http://hub.kc9zhv.com

2 2

Web transceiver Certificate Expired
by Tim Sawyer 02 Jul '15

02 Jul '15

The Java certificate for the Webtranceiver has expired and will not be renewed. But you can add an exception to your Java security settings in the control panel or system preferences. FYI, if anybody wants to step up and sign the Jar file please let me know. -- Tim

1 0

Autopatch settings
by Mark Johnston 02 Jul '15

02 Jul '15

Does anyone know a way to do either of these? With a simplex node i.e. Duplex set to 0/1 in rpt.conf the Autopatch operates in vox mode, is there a way to force this in Duplex =3 without rewriting the source code? or Is there a way to set a time out timer on the phone side, as it transmits 100% of the time during the call, I would like to have it drop after 9 mins, if the user keys up, it would reset/continue or at least drop and come back up in some fashion... some cop or other command to unkey the tx briefly - my transmitter has a built in 10min TOT - wanted a way to reset it on the autopatch calls.

1 0

Radio relax
by Robert Newberry 02 Jul '15

02 Jul '15

I am getting a lot of TT falsing on my node. I did some googling and found this. > On Sun, Jun 3, 2012 at 4:01 PM, Tim Sawyer <tim.sawyer at me.com> wrote: > First I would update from svn, might as well as you have to recompile anyway. The instructions to update from svn are at https://allstarlink.org/support.html#astupgrade > > Before you do the make up grade edit /usr/src/astsrc/asterisk/menuselect.makeopts > change the line that says > > MENUSELECT_CFLAGS=RADIO_RELAX LOADABLE_MODULES > to > MENUSELECT_CFLAGS=LOADABLE_MODULES > > then do make upgrade or make upgrade-acid as appropriate. > -- > Tim > :wq I also followed the link to the upgrade instructions. https://allstarlink.org/support.html#astupgrade Will I still need to do this after? http://docs.allstarlink.org/drupal/node/111 I just want to make sure I have good instructions before I procede. Thanks N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812

2 1