- App_rpt-users - lists.keekles.org

PTT/VOX Issues with Remote Node and Autopatch
by k2dls＠arrl.net 05 Jul '14

05 Jul '14

I currently have a Hub Node setup. A radio node will follow. My goal for the moment is for a remote node to connect to my hub and then for my hub to initiate an IAX call over to my asterisk PBX where it will ring a particular extension. This mostly works, but the remote node remains keyed up throughout the connection. I am seeking a solution. Based upon a suggestion from Mike the Midnight Engineer, I took a look at the events programming description. I was able to figure out after a few reads how to use the RPT_NUMLINKS variable to trigger an autopatch dial macro when the value goes from false to true. So a remote connection comes into my hub and the designated extension on my PBX rings. Audio is passed both directions. However, as stated above, no PTT control. I have looked at the duplex and vox timeout configuration variables and have tried a number of approaches without success. Any thoughts or direction would be most appreciated. Thanks, Dan K2DLS

1 0

Re: [App_rpt-users] Run Macro on Connection
by mike＠midnighteng.com 05 Jul '14

05 Jul '14

2 2

Run Macro on Connection
by k2dls＠arrl.net 05 Jul '14

05 Jul '14

I want to automatically run a macro upon receipt of a connection from another node. Is there a way to do this? Thanks for any assistance. 73, Dan K2DLS

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 65, Issue 13
by Steve Liggett 05 Jul '14

05 Jul '14

TROUBLE GETTING Registered That did it. The network file was empty. Thank you. steve W3RX > Message: 5 > Date: Fri, 04 Jul 2014 07:59:59 -0400 > From: Jon Rorke <jrorke(a)cogeco.ca> > To: app_rpt-users(a)ohnosec.org > Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 65, Issue 8 > Trouble Getting Registered > Message-ID: <53B6973F.6050003(a)cogeco.ca> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > When you switch your node from DHCP to static IP, the name server in > resolv.conf gets blown away. So the box doesn't get dns access. > > So edit your /etc/resolv.conf file and put a name server of: > > nameserver 8.8.8.8 > > Reboot, then you should be able to connect out and in. > > By the way you may need to wait 10 -15 minutes before thew node is fully > active. Once you node shows up in the Allstar active node list, it takes > that long before most nodes find you IP address. > > If you have dhcp set up this file automatically gets populated with a > DNS that points to your IP provider or local router IP. > > Jon VA3RQ > On Jul 4, 2014, at 8:00 AM, app_rpt-users-request(a)ohnosec.org wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. Problem with audio from portable radio device to phone > (Cristian Gonz?lez Flores) > 2. Re: Problem with audio from portable radio device to phone > (Jim Duuuude) > 3. New IP - node disconnects - Hungup... (Bob) > 4. ACID Capabilities (Robert) > 5. Re: App_rpt-users Digest, Vol 65, Issue 8 Trouble Getting > Registered (Jon Rorke) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Thu, 3 Jul 2014 16:12:52 -0400 > From: Cristian Gonz?lez Flores <cr.gonzalez.flores(a)gmail.com> > To: app_rpt-users(a)ohnosec.org > Subject: [App_rpt-users] Problem with audio from portable radio device > to phone > Message-ID: > <CAMKDKoK2MT7OUuygcsqKLAmEjQpGbJXjuPdfq+1f9-KxuPVyAw(a)mail.gmail.com> > Content-Type: text/plain; charset="utf-8" > > Hi > > What is the difference between: > > .- URI to Simplex Motorola Cable > .- URI to Duplex Motorola Cable > > Because we bought a while ago the first one and we have only audio from > Phone-URI-GM300 to Portable radio device and not from Portable radio device > to GM300->URI->Phone. > > The person who programmed the GM300 left him a bridge in the rear port, > with that bridge could be heard through the speaker of the GM300 which was > spoken in the portable radio device, but to connect the URI was necessary > to remove the bridge and place the URICABLE since then not the speaker of > the GM300 is heard. > > Our project is the following, from an IP phone to make a call to a radio. > At this time we can call smoothly and through * 99 talk to the radio and > heard perfect, however, speaking on the radio cant be heard on the phone. > What could be the problem? > > Please your help and thank you su much in advance. >

1 0

iaxRpt Client SCAN help
by James R. Pilgram 05 Jul '14

05 Jul '14

Aloha, Trying to get the SCAN feature of the iaxRpt Client to work. I have multiple nodes not connected together that I would like to be able to monitor when they become active. I have checked the help and support tab and google to no avail. I find mentions but no explanations of what the tick boxes actually do. Looking at the Options/Preferences/Scan tab, in the box next to SCAN TYPE: there are no options. What should go in there if anything? Is there a "poop sheet" on setting this up that I missed. Any help appreciated. Jim NH6HI

3 2

Few CLI questions
by Robert Newberry 04 Jul '14

04 Jul '14

I have a few questions, I moved the server from my home location to the repeater location about 20 miles from home. As far as I can tell everything in terms of making a connection to the outside world went OK. I have a few issues that I cant figure out. 1. I created a SIP and IAX connection for my tablet and cellphone to experiment with. Those worked fine at home and the only thing different is the net work. When I connect on SIP the node will not recognize any DTMFs when I connect via IAX it will recognize DTMFs. Is there a way to watch thru the CLI if it's receiving DTMFs to determine whats happening? I also get this error on the new network that I didn't see at home. [Jul 4 21:56:02] WARNING[4042]: chan_iax2.c:921 jb_warning_output: Resyncing the jb. last_delay -3774, this delay -47807, threshold 8170, new offset 43858 Is this anything I should be concerned about? I have a few other SIP issues but I'd better take it a few at a time. Thank you

1 0

Changing courtesy tones
by Mark Johnston 04 Jul '14

04 Jul '14

Happy 4th to everyone, Trying to figure out where I am going wrong in changing the courtesy tone(s) specifically the linked tone i.e. when other users unkey on the remote nodes... I thought this was as simple as changing ct8=.... and run asterisk -rx "module reload" and even rebooted, did not change the tone at all - and what is the best way to reload these settings? [28344] ; Change this to your assigned node number rxchannel=voter/28344 duplex=2 ; was 0 and was 3 ;erxgain=-3 ;etxgain=3 ;controlstates=controlstates scheduler=schedule28344 morse=morse28344 macro=macro28344 functions=functions28344 phone_functions=functions28344 link_functions=functions28344 telemetry=telemetry28344 wait_times=wait-times context = radio callerid = "Repeater" <0000000000> idrecording = |iKC7DMF accountcode=RADIO hangtime=100 althangtime=100 totime=530000 idtime=540000 politeid=3000 idtalkover=|iKC7DMF unlinkedct=ct2 remotect=ct3 linkunkeyct=ct8 nolocallinkct=1 ;eannmode=1 ;connpgm=yourconnectprogram ;discpgm=yourdisconnectprogram ;lnkactenable=0 ;lnkacttime=1800 ;lnkactmacro=*52 ;lnkacttimerwarn=30seconds ;remote_inact_timeout=1800 ;remote_timeout=3600 nounkeyct=0 ;holdofftelem=0 beaconing=0 linktolink=yes telemdefault=2 propagate_dtmf = yes propagate_phonedtmf = yes outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - | /usr/bin/ezstream -qvc /etc/ezstream.xml ; ; *** Status Reporting *** ; ; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org ; depending on whether you are running ACID or Limey Linux. ; ** For ACID *** statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates [schedule28344] ;dtmf_function = m h dom mon dow ; ala cron, star is implied [functions28344] 1=ilink,1 2=ilink,2 3=ilink,3 4=ilink,4 5=macro,1 70=ilink,5 71=ilink,6 72=ilink,7 73=ilink,15 74=ilink,16 75=ilink,8 76=ilink,12 ; Permanently connect specified link -- monitor only 77=ilink,13 ; Permanently connect specified link -- transceive 80=status,1 81=status,2 90=cmd,/home/irlp/scripts/WX/ZIPCODE/Forecast A=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up D=autopatchdn ; Autopatch down [telemetry28344] ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(1800,100,120,3000)(1300,100,120,3000)(1750,100,120,3000)(1000,100,120,3000); Star Trek ct3=|t(440,0,150,4096) ct4=|t(550,0,150,2048) ct5=|t(660,0,150,2048) ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(1800,100,120,3000)(1300,100,120,3000)(1750,100,120,3000)(1000,100,120,3000); Star Trek ct9=|t(1800,100,120,3000)(1300,100,120,3000)(1750,100,120,3000)(1000,100,120,3000); Star Trek remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000); remotemon=|t(1209,0,50,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) patchup=rpt/callproceeding patchdown=rpt/callterminated ;telemdefault=0 phonelinkdefault=0

4 3

ACID Capabilities
by Robert 04 Jul '14

04 Jul '14

I was all set to begin setting up a server using a dual processor AMD because I have one gathering dust. I'm told that I don't need a "server" but a 1U was given to me and the opportunity to mount it at a data center. I don't see a 64-bit distro so I'm assuming that only x86? The 64-bit AMD Opteron 275 as I recall can use the instruction set of x86 and I'm okay with overkill. I thought that if I had anything extra I could maybe share with the less fortunate, although I don't know my own needs yet. This server has 8GB of RAM and I was going to change the RAID to a SD drive. I've loaded CentOS many, many times and I know that the standard distro can handle a dual processor but can the Acid distro? I guess I figured that if a P4 2.8GHz can handle 4 nodes than a dual processor should be able to handle 8 if the kernel allows a dual proc. I'd appreciate a moment of someone's time to tell me if I can use what I have and save some money. I don't need to get all fancy; I was trying to save money and buy the RTCM. Thanks in advance.

2 1

CuBox-i.. next port?
by pete M 04 Jul '14

04 Jul '14

http://www.solid-run.com/wiki/index.php?title=Main_Page Seen the little gadget and here is the list of the OS it can handle. http://www.solid-run.com/wiki/Category:Distribution Seem a nice little thing to play with.. I am ordering one to be my new xbmc server for the 110 inch 2k-4k projector in the basement.. Think I will get a second one if it run good.

1 0

Re: [App_rpt-users] ACID Capabilities
by mike＠midnighteng.com 04 Jul '14

04 Jul '14

1 0