- App_rpt-users - lists.keekles.org

Re: [App_rpt-users] Changing Courtesy Tones, and SSHing into the computer
by Skyler F 28 Apr '14

28 Apr '14

Thanks for the GSM files. So, OK. First, are you sure that 10.0.1.1 is the address assigned to your > node computer and not to the Airport router? Usually, the address at then > eginning of a block like that is the router. So you’re likely trig to ssh > to the wrong place. Do you have direct access to the node computer, i.e. is > there a keyboard and monitor on it? If so, you should be able to find your > correct internal IP by typing ifconfig eth0 > Thanks! I typed ifconfig eth0 and I was 10.0.1.23!! Stupid ME I Was not even port forwarding to the right address! I have no idea how it worked even to a few nodes without port forwarding but 28298 works now as well as the web transciever! On Fri, Apr 18, 2014 at 3:53 PM, Skyler F <electricity440(a)gmail.com> wrote: > I meant to reply all, sorry if you recieve this twice > > > On Fri, Apr 18, 2014 at 3:53 PM, Skyler F <electricity440(a)gmail.com>wrote: > >> Stupid ME I Was not even port forwarding to the right address! I have no >> idea how it worked even to a few nodes without port forwarding but 28298 >> works now as well as the web transciever! >> >> >> On Fri, Apr 18, 2014 at 3:33 PM, Skyler F <electricity440(a)gmail.com>wrote: >> >>> Thanks for the GSM files. >>> >>> So, OK. First, are you sure that 10.0.1.1 is the address assigned to >>>> your node computer and not to the Airport router? Usually, the address at >>>> then eginning of a block like that is the router. So you’re likely trig to >>>> ssh to the wrong place. Do you have direct access to the node computer, >>>> i.e. is there a keyboard and monitor on it? If so, you should be able to >>>> find your correct internal IP by typing ifconfig eth0 >>>> >>> >>> Thanks! I typed ifconfig eth0 and I was 10.0.1.23!! >>> >>> >>> >>> >>> On Fri, Apr 18, 2014 at 1:51 PM, Fred McLean <FredM(a)fredsportraits.com>wrote: >>> >>>> Skyler, (copy of the email I just sent to the group with two attached >>>> gsm files) >>>> >>>> >>>> >>>> If you learn the trick to convert a Microsoft wav to ULAW, please let >>>> me know! >>>> >>>> >>>> >>>> I convert or create the wav file top 8000 just as you do. Instead of >>>> worrying much about ULAW files I just convert it to a gsm file. >>>> >>>> >>>> >>>> To convert a 16000 or 8000 Hz wav to gsm. (I think it will work with >>>> both) >>>> >>>> Use the command line, not the CLI. >>>> >>>> Go to the directory where your newly copied wav file is located. >>>> >>>> Type in the following command to change to that directory. >>>> >>>> The below example is assuming you create a folder named “custom”. >>>> >>>> >>>> >>>> cd /var/lib/asterisk/sounds/custom >>>> >>>> >>>> >>>> Your prompt should look similar to this. w0fcm is my server name. >>>> >>>> [root@w0fcm custom]# >>>> >>>> >>>> >>>> Input the following command substituting your wav file name and your >>>> new gsm file name. >>>> >>>> Here I used the name example.wav and example.gsm. >>>> >>>> sox example.wav -r 8000 example.gsm >>>> >>>> >>>> >>>> Delete the wav file and any ulaw or sln files with the same prefix in >>>> the folder you are working with. >>>> >>>> >>>> >>>> If you want to play a file locally input the following command. >>>> >>>> Note: 29503 is the node number I am playing it on. >>>> >>>> >>>> >>>> /usr/sbin/asterisk -rx "rpt localplay 29503 custom/example" >>>> >>>> >>>> >>>> If you want to play a sound file globally input the following command. >>>> >>>> /usr/sbin/asterisk -rx "rpt playback 29503 custom/example" >>>> >>>> >>>> >>>> To replace a tone with a sound file just remove or comment out the >>>> codes and replace it with a folder and file prefix. Below are three >>>> examples of tones/sounds I use for remotetx. >>>> >>>> >>>> >>>> [telemetry] >>>> >>>> remotetx=custom/beep >>>> >>>> ;remotetx=custom/screen >>>> >>>> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000); Original >>>> >>>> ;remotetx=|t(1800,100,120,3000)(1300,100,120,3000)(1750,100,120,3000)(1000,100,120,3000); >>>> Star Trek >>>> >>>> ;remotetx=|t(1173,100,120,3000)(1316,100,120,3000)(1045,100,120,3000)(523,100,120,3000)(783,100,120,3000); >>>> Close Encounters >>>> >>>> >>>> >>>> Let me know if you have any questions. >>>> >>>> >>>> >>>> 73 >>>> >>>> Fred McLean >>>> >>>> w0fcm 29503 >>>> >>>> >>>> >>>> >>>> >>>> *From:* Skyler Fennell [mailto:electricity440@gmail.com] >>>> *Sent:* Friday, April 18, 2014 12:07 PM >>>> *To:* Mark Johnston >>>> *Cc:* app_rpt-users(a)ohnosec.org >>>> *Subject:* Re: [App_rpt-users] Changing Courtesy Tones, and SSHing >>>> into the computer >>>> >>>> >>>> >>>> I did not restart the sshd after I changed port 222 to 22. I did reboot >>>> the computer, but Maybe that's not enough. So just run "/etc/rc3.d/S55sshd >>>> restart"? >>>> >>>> >>>> >>>> I got really confused with all of those random numbers under telemetry >>>> section, but I guess they are all frequencies for the Courtesy tone. >>>> >>>> >>>> >>>> On audacity, I just did file > export then I chose other uncompressed >>>> format and did Microsoft wav, ULAW. I also made sure the project rate was >>>> at 8000. >>>> >>>> >>>> >>>> When I get home, I will check the files, and test the telephone portal. >>>> >>>> >>>> >>>> 73 (or *72 in allstar) >>>> >>>> Skyler Kd0whb >>>> >>>> >>>> >>>> >>>> >>>> >>>> Sent from my iPhone >>>> >>>> >>>> On Apr 18, 2014, at 10:22 AM, Mark Johnston <markjohnston73(a)gmail.com> >>>> wrote: >>>> >>>> SSH: I assume you restarted the sshd after changing the port or reboot >>>> the allstar box either way - /etc/rc3.d/S55sshd restart >>>> >>>> should do it. >>>> >>>> >>>> >>>> Btw what is the trick to getting uLaw files via Audacity? >>>> >>>> >>>> >>>> Courtesy tones, have to look under the [Telemetry] section >>>> >>>> and change the freq/numbers there - >>>> >>>> in /etc/asterisk/rpt.conf >>>> >>>> >>>> >>>> do you have the line in rpt.conf? >>>> >>>> >>>> >>>> <node> = radio(a)127.0.0.1/<node>,NONE >>>> >>>> >>>> >>>> And the one in /etc/asterisk/iax.conf >>>> >>>> register=<node>:<secret>@register.allstarlink.org >>>> >>>> >>>> >>>> Assuming the port 4569 is setup correctly, can you connect from the >>>> allstar dial in # from any std telephone? >>>> >>>> >>>> >>>> >>>> >>>> >>>> "Got Root?" >>>> >>>> >>>> >>>> How many software engineers does it take to change a light bulb? >>>> >>>> *None. It's a hardware problem.* >>>> >>>> >>>> >>>> >>>> >>>> Unix is user friendly. It's just very particular about who it's friends >>>> are. >>>> >>>> WINDOWS: Will Install Needless Data On Whole System >>>> >>>> MICROSOFT: Most Intelligent Customers Realize Our Software Only Fools >>>> Teenagers. >>>> >>>> >>>> >>>> >>>> >>>> A ntennas >>>> P oorly >>>> P laced >>>> L acks >>>> E ngineering >>>> >>>> The best way to accelerate a computer running Windows is at 9.81 m/s². >>>> >>>> >>>> >>>> *"I get paid to support Windows, I use Linux to get work done."* >>>> >>>> >>>> >>>> On Fri, Apr 18, 2014 at 7:14 AM, Skyler F <electricity440(a)gmail.com> >>>> wrote: >>>> >>>> Hello, >>>> >>>> I am new ham in high school, and finally got a little SIMPLEX repeater >>>> up and running. >>>> >>>> >>>> >>>> *My first question* Is about SSHing into the computer remotely. I >>>> first gave it a try on my LAN, because I knew port forwarding would not be >>>> required. >>>> >>>> First, I *Changed *the port 222 to port 22 on the SSHD_Config file >>>> >>>> >>>> >>>> We are using an apple airport router, which states the LAN address of >>>> the Ethernet port is 10.0.1.1. I typed ssh root(a)10.0.1.1, and I got a >>>> connection refused. >>>> >>>> I was able to reverse SSH back to my macintosh using ssh >>>> username@computersLANip from ACID, but when I tried to SSH back to >>>> acid, it would not work. Just Connection Refused. >>>> >>>> >>>> After I login on ACID it says Root@Skylersnode, my node, and I also >>>> gave ssh root@<node number> and ssh skylersnode@local IP a try, but >>>> still no success. >>>> >>>> >>>> >>>> Are there any suggestions on getting this to work? >>>> >>>> >>>> >>>> *Second question: Courtesy tones,* >>>> >>>> >>>> >>>> I just figured out how to create a ULAW on audacity, and mount a flash >>>> drive on the command, and I am wondering if I can change the courtesy tones >>>> or any other audio file. Like the "I OWN COMMAND" annoying thing. Where >>>> would the courtesy tones be located, and under what file name? >>>> >>>> >>>> >>>> *Third question: *why it wont work on the web transceiver >>>> >>>> When I dial in the node on the web transceiver, nothing happens, and >>>> when I hit the connect button, it does not do anything. Is there any way to >>>> get it to work, or will the web transceiver not work with my node. I would >>>> think it should work, because I have almost the same setup as Willem's >>>> node, 29571<https://allstarlink.org/portal/webtransceiver-frameset.php?nodenum=29571>,on saddle back mountain. >>>> >>>> *Last Question: Won't connect to 28298 or 28299* >>>> >>>> This node is part of the FUN system here in Colorado, and I tried >>>> dialing 28298, which belongs to Jeff KØJSC, but I heard nothing, not even >>>> the change in courtesy tone. He has no idea why my node will not connect >>>> up, but it is weird because it won't even show up on the web transceiver. >>>> >>>> Thanks >>>> >>>> Skyler KDØWHB >>>> >>>> >>>> _______________________________________________ >>>> App_rpt-users mailing list >>>> App_rpt-users(a)ohnosec.org >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> >>>> To unsubscribe from this list please visit >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >>>> down to the bottom of the page. Enter your email address and press the >>>> "Unsubscribe or edit options button" >>>> You do not need a password to unsubscribe, you can do it via email >>>> confirmation. If you have trouble unsubscribing, please send a message to >>>> the list detailing the problem. >>>> >>>> >>>> >>>> >>> >> >

2 5

Re: [App_rpt-users] this may help others with zaptel issues on some hardware
by AH2S 27 Apr '14

27 Apr '14

Hi Mark, Yes. It is indeed the Dell PowerEdge Server at the colo facility. I took another shot at it before completely giving up. After having eliminated most everything else, it came down to hardware. That's when I started exploring other, less obvious and arguably less likely solutions. The disabling of ACPI was nothing more than a guess in a list of things I began to try, one at a time. I can't explain how ACPI would interfere with zaptel but it does, at least on my server. Pretty strange. I'm just glad I figured it out and it's working now! --- Rob Pectol - AH2S AllStar Node 2147 On 2014-04-27 18:20, Mark Guibord wrote: > Hi Rob, > > I take it you are talking about your Dell 64 bit machine at the > colocation > right? If so congratulations, I'm amazed that the Advanced > Configuration and > Power Interface (ACPI) would interfere with the Zaptel driver. > > Mark - K7IZA > > -----Original Message----- > From: app_rpt-users-bounces(a)ohnosec.org > [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of AH2S > Sent: Saturday, April 26, 2014 10:25 PM > To: App_rpt Users > Subject: [App_rpt-users] this may help others with zaptel issues on > some > hardware > > In case there are others that have come across issues getting an ACID > server > up and running where the zaptel driver is misbehaving, this one little > gem > of info might make all the difference in the world! I had previously > tried > everything I could think of, including a dozen different kernels and > associated build environments, each time recompiling Asterisk and > associated > drivers (zaptel being one of them, of course). But nothing worked. > The > zaptel driver refused to function even though it appeared to load up > just > fine. I just couldn't get it to work no matter what I did. In > frustration > I put it aside for a few weeks. Well, I just recently got back to it > but > this time I found success! Here's my solution: > > Disable acpi at boot up. You can do this by appending, "acpi=off" to > the > kernel boot parameters in the grub boot loader. For example on my > CentOS > 5.1 system I modified the /boot/grub/menu.lst entry for my kernel boot > parameters as follows: > > kernel /boot/vmlinuz-2.6.18-348.12.1.el5PAE ro root=LABEL=/ acpi=off > > Save the file and reboot. This one little thing made the difference > between > having a useless ACID install on hardware at a colocation facility > 8,000 > miles away, to a fully functional AllStar Server handling several > remote > RTCMs! I had all but given up hope on getting the zaptel driver to > work > properly on this hardware until I tried this on a whim! > Since I haven't seen this info posted anywhere yet, I thought I'd offer > it > up to the group in the hopes that it might help someone else. > > -- > Rob Pectol - AH2S > AllStar Node 2147 > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > down to > the bottom of the page. Enter your email address and press the > "Unsubscribe > or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to > the list detailing the problem.

1 0

Re: [App_rpt-users] usbradio to simpleusb
by Bob 27 Apr '14

27 Apr '14

Very good. Since I'm using the same USB device, can I just copy over the settings for simpleusb? Trying this approach because I discovered PL was generated in the radio. Thanks, Bob kk6ecm _____ From: hotmail_97fc649978f54bf0(a)live.com [mailto:hotmail_97fc649978f54bf0@live.com] On Behalf Of Doug Crompton Sent: Saturday, April 26, 2014 9:54 PM To: Bob Cc: app_rpt-users(a)ohnosec.org Subject: RE: [App_rpt-users] usbradio to simpleusb simpleusb as its name implies depends on the radio to do much of the work. The PL for RX and TX must be in the radio. The radios squelch is used. So just worry about what needs to be setup in simpleusb. You need RX and TX audio, PTT and COS. You can select whether PTT and/or COS are inverted. Otherwise there is not much to setup. Just run the simpleusb audio setup and you should be good to go. If you can use simpleusb it works very well. I use it exclusively and so do many others I know who run Allstar. Probably the reason more people don't run it is because usbradio is the default config and it requires a COS signal. Some people just like complication. I do not! 73 Doug WA3DSP http://www.crompton.com/hamradio _____ From: kk6ecm(a)gmail.com To: app_rpt-users(a)ohnosec.org Date: Sat, 26 Apr 2014 21:15:01 -0700 Subject: Re: [App_rpt-users] usbradio to simpleusb When moving from usbradio to simpleusb, I noticed there are more inputs in usbradio_tune... compared to simpleusb_tune. What is the usbradio "rxvoiceadj," and why is it not used in simpleusb? thanks, Bob kk6ecm _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

3 2

this may help others with zaptel issues on some hardware
by AH2S 27 Apr '14

27 Apr '14

In case there are others that have come across issues getting an ACID server up and running where the zaptel driver is misbehaving, this one little gem of info might make all the difference in the world! I had previously tried everything I could think of, including a dozen different kernels and associated build environments, each time recompiling Asterisk and associated drivers (zaptel being one of them, of course). But nothing worked. The zaptel driver refused to function even though it appeared to load up just fine. I just couldn't get it to work no matter what I did. In frustration I put it aside for a few weeks. Well, I just recently got back to it but this time I found success! Here's my solution: Disable acpi at boot up. You can do this by appending, "acpi=off" to the kernel boot parameters in the grub boot loader. For example on my CentOS 5.1 system I modified the /boot/grub/menu.lst entry for my kernel boot parameters as follows: kernel /boot/vmlinuz-2.6.18-348.12.1.el5PAE ro root=LABEL=/ acpi=off Save the file and reboot. This one little thing made the difference between having a useless ACID install on hardware at a colocation facility 8,000 miles away, to a fully functional AllStar Server handling several remote RTCMs! I had all but given up hope on getting the zaptel driver to work properly on this hardware until I tried this on a whim! Since I haven't seen this info posted anywhere yet, I thought I'd offer it up to the group in the hopes that it might help someone else. -- Rob Pectol - AH2S AllStar Node 2147

1 0

Re: [App_rpt-users] usbradio to simpleusb
by Bob 27 Apr '14

27 Apr '14

When moving from usbradio to simpleusb, I noticed there are more inputs in usbradio_tune... compared to simpleusb_tune. What is the usbradio "rxvoiceadj," and why is it not used in simpleusb? thanks, Bob kk6ecm

2 1

Re: [App_rpt-users] URI and URIx Testing
by Bob 27 Apr '14

27 Apr '14

Most recent ACID distro from Allstarlink.org. Gigabyte C1007UN-D with 4 gig memory, and an SSD SATA drive. Built in with an IntelR Dual-core CeleronR 1007U processor (1.5 GHz) lsusb -v reports the URI and the URIx both as USB 1.1 Thanks, Bob kk6ecm _____ From: Chris Andrist [mailto:chris@yeahmon.net] Sent: Friday, April 25, 2014 6:02 PM To: Bob Subject: Re: [App_rpt-users] URI and URIx Testing Bob, Tell us about the computer you are running this on and what Distro you are using? Just as an FYI. ACID runs best on Pentium 4 computers and slower. -- Regards, Chris Andrist, KC7WSU On Apr 25, 2014, at 6:59 PM, "Bob" <kk6ecm(a)gmail.com> wrote: I'm at a loss... looking for ideas on how to proceed... Still attempting to get our repeater working... rebuilt the computer that crashed, and it works well... Getting strange results when connecting the URI back to the radio (can't find anything wrong there). The fact I can't seem to get a URI, or URIx working with my computer suggests a possible issue with my setup. I have some inputs from folks for changes in the usbradio, or simpleusb which I'd like to check, but need to confirm the URI is working correctly, so I'm not chasing hardware issues by looking at software. I tested my URI using the loopback diagram and uridiag; it passes all the digital, and fails all the analog. I procured a URIx for replacement, and built up the loopback connector for it and tested, same results. I've checked and rechecked my wiring of the loopback connector. The URIx uses two 1k resistors and two extra jumpers than the URI (see below), and the URI two 10k resistors per DMK folks. (There is a confirmed error in the uridiag listed connections). I did not connect the URIx 12 and 20 (Blk and Wht) leads, nor the power supply to activate the 2x amplifier (pins 13 & 25), which I am not using. I'm told the correct connections are as shown below from the URI-FAQ.pdf, with change of 1K for 10K for URIx per DMK, and comparing with the URIx test fixture. Assuming the URIx was good from the factory, and all I did was connect it up to the loopback and computer, turn on the computer with ACID # service asterisk stop # uridiag URIDiag, diagnostic program for the DMK Engineering URI USB Radio Interface, version 0.8, 04/26/11 Found CM119 USB Radio Interface at 001/003 . . . Enter your selection:t Testing digital I/O (PTT,COR,TONE and GPIO).... Digital I/O passed!! Testing Analog at 204 (and 700) Hz... Analog level on left channel for 204.0 Hz (0.0) is out of range!! . . . 24 Error(s) found during test(s)!!!! URI Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 10K Resistor between Pins 21 and 22 10K Resistor between Pins 21 and 23 URIx Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 1K Resistor between Pins 21 and 22 1K Resistor between Pins 21 and 23 Pin 5 to Pin 10 Pin 6 to Pin 11 sigh! Thanks, Bob kk6ecm _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

4 6

URI and URIx Testing
by Bob 26 Apr '14

26 Apr '14

I'm at a loss... looking for ideas on how to proceed... Still attempting to get our repeater working... rebuilt the computer that crashed, and it works well... Getting strange results when connecting the URI back to the radio (can't find anything wrong there). The fact I can't seem to get a URI, or URIx working with my computer suggests a possible issue with my setup. I have some inputs from folks for changes in the usbradio, or simpleusb which I'd like to check, but need to confirm the URI is working correctly, so I'm not chasing hardware issues by looking at software. I tested my URI using the loopback diagram and uridiag; it passes all the digital, and fails all the analog. I procured a URIx for replacement, and built up the loopback connector for it and tested, same results. I've checked and rechecked my wiring of the loopback connector. The URIx uses two 1k resistors and two extra jumpers than the URI (see below), and the URI two 10k resistors per DMK folks. (There is a confirmed error in the uridiag listed connections). I did not connect the URIx 12 and 20 (Blk and Wht) leads, nor the power supply to activate the 2x amplifier (pins 13 & 25), which I am not using. I'm told the correct connections are as shown below from the URI-FAQ.pdf, with change of 1K for 10K for URIx per DMK, and comparing with the URIx test fixture. Assuming the URIx was good from the factory, and all I did was connect it up to the loopback and computer, turn on the computer with ACID # service asterisk stop # uridiag URIDiag, diagnostic program for the DMK Engineering URI USB Radio Interface, version 0.8, 04/26/11 Found CM119 USB Radio Interface at 001/003 . . . Enter your selection:t Testing digital I/O (PTT,COR,TONE and GPIO).... Digital I/O passed!! Testing Analog at 204 (and 700) Hz... Analog level on left channel for 204.0 Hz (0.0) is out of range!! . . . 24 Error(s) found during test(s)!!!! URI Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 10K Resistor between Pins 21 and 22 10K Resistor between Pins 21 and 23 URIx Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 1K Resistor between Pins 21 and 22 1K Resistor between Pins 21 and 23 Pin 5 to Pin 10 Pin 6 to Pin 11 sigh! Thanks, Bob kk6ecm

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 62, Issue 66
by Malcolm Good 26 Apr '14

26 Apr '14

Hi Tim This development is great. I wasn't expecting this for months. I look forward to implementing when I get back home. Once again thanks for making avaliable you code. Mal sent from my Samsung Note On 26/04/2014 12:00 AM, <app_rpt-users-request(a)ohnosec.org> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > Today's Topics: > > 1. Allmon Control Panel (Tim Sawyer) > > > ---------- Forwarded message ---------- > From: Tim Sawyer <tim.sawyer(a)mac.com> > To: Allstar Users <app_rpt-users(a)ohnosec.org> > Cc: > Date: Thu, 24 Apr 2014 17:02:08 -0700 > Subject: [App_rpt-users] Allmon Control Panel > Allmon can now do pretty much anything that can be done at the Asterisk > CLI giving you complete web based control of your nodes. > > The Allmon Control Panel is a popup window which allows selected commands > to be issued through the Asterisk Manager Interface. The command selection > is configured with an ini file allowing the Allmon admin set up virtually > any AMI command. The included sample ini show you just some of the things > you can do. > > Users must login to see the new Control Panel button. If more than one > node is display, select a node from the drop down and them press Control > Panel. > > Please grab the latest Allmon at my gtihub at > https://github.com/tsawyer/allmon/tree/allmon2 > > Enjoy, > — > Tim WD6AWP > :wq > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >

1 0

Back from the hospital
by Jim Duuuude 25 Apr '14

25 Apr '14

Well, once again, I found myself needing to go to the hospital on Sunday. I am back now, and feeling much better. That is why I was not responding to emails. Jim

3 2

How to stream live audio from URI to broadcast software.
by Loren Tedford 24 Apr '14

24 Apr '14

Hello my name is Loren I would like to set up a live audio stream from my repeater to broadcastify if anyone has any suggestions on how or what i should do this would be appreciated. I would much rather if I could just take the audio from the repeater its self rather than setting up a secondary scanner then reroute it back to broadcastify.. Using Acid Linux Distro all normal install.. URI connected to two GM300s etc.. Any suggestions on this idea and if you have done this before please let me know how ya did this or what i need to do to get started 73's for now. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Email: loren(a)lorentedford.com http://www.lorentedford.com

2 1