- App_rpt-users - lists.keekles.org

May have figured out stats problem
by Michael Wolthuis 30 Dec '13

30 Dec '13

NTP was failing to connect to a server and thus the Beagleboard thought it was 1970. Hopefully this will fix it, thanks, Mike - kb8zgl

1 0

In the CLI
by Michael Wolthuis 30 Dec '13

30 Dec '13

I am seeing the following in the CLI. [Feb 12 02:55:41] NOTICE[25454]: chan_iax2.c:9712 socket_process: Registration of 'A28881' rejected: 'Registration Refused' from: '67.215.233.178' [Feb 12 02:55:41] NOTICE[25456]: chan_iax2.c:9712 socket_process: Registration of 'A28241' rejected: 'Registration Refused' from: '67.215.233.178'

2 3

Status not updating in Portal
by Michael Wolthuis 30 Dec '13

30 Dec '13

My two nodes 28241 and 28881 on a Beagleboard are not updating their statuses on the portal. The maps look good on the nodes they are connected too. Anyone have any pointers, I haven¹t been able to figure it out? I have everything in the config file looking right, at least I think. Mike kb8zgl

1 0

Question regarding interfacing to a Kenwood Nextedge Repeater NXR-710/810
by Lu Vencl 30 Dec '13

30 Dec '13

I know this is a shot in the dark and I am probably the only one trying this, but is there by chance anyone that has successfully interfaced a URI to a Kenwood NEXEDGER Repeater NXR-710/810? My challenge is this. 1. Can't seem to find a way to feed in pre-emphasize TX audio.. Not a show stopper, but sure would be nice if I could. I can always run regular mode.. Tried the TX data input but got no audio 2. When using external PTT, it mutes the TX audio for some reason. Seems as when the repeater is receiving audio, and the URI bring PTT low on the External PTT, it mutes the audio completely. You hear no repeat audio. I am using in rpt.conf, Duplex =1.. If I do Duplex =0, then I get the internal repeat audio, but it does not take advantage of the Allstar processed audio such as audio delay and DTMF muting. There has to be a better way and has hoping someone has already succeeded in this challenge. I can email you the programming file to the repeater if you wish. Thanks in advance. Lu, KA4EPS

6 8

New node unable to connect to it.
by Steve Denbow 29 Dec '13

29 Dec '13

Hello All, Just put a new node (hub) online and I am unable to connect to it from my established node, but I can connect to it via the phone portal It show as registered on the portal, and this is the error I get... -- Hungup 'Zap/pseudo-160683732' [Dec 29 20:08:07] NOTICE[8435]: chan_iax2.c:4071 __auto_congest: Auto-congesting call due to slow response -- Hungup 'IAX2/75.74.231.119:4569-2295' -- Hungup 'Zap/pseudo-504507930' -- Remote UNIX connection -- Remote UNIX connection disconnected -- Remote UNIX connection -- Remote UNIX connection disconnected -- Remote UNIX connection -- Remote UNIX connection disconnected -- <Zap/pseudo-1833289829> Playing 'rpt/node' (language 'en') -- <Zap/pseudo-1833289829> Playing 'digits/2' (language 'en') -- <Zap/pseudo-1833289829> Playing 'digits/7' (language 'en') -- <Zap/pseudo-1833289829> Playing 'digits/5' (language 'en') -- <Zap/pseudo-1833289829> Playing 'digits/4' (language 'en') -- <Zap/pseudo-1833289829> Playing 'digits/5' (language 'en') -- <Zap/pseudo-1833289829> Playing 'rpt/connection_failed' (language 'en') -- Hungup 'Zap/pseudo-1833289829' I can ping the IP address and the round trip average is 85ms with 0% of packets lost. Thanks! -- Steve Denbow | KD8BIW Ohio 220 Group (419)606-5774 Mobile kd8biw(a)gmail.com www.kd8biw.com

2 1

Re: [App_rpt-users] iax2 registry issue
by Geoff Edmonson 29 Dec '13

29 Dec '13

Instead of a reboot, restart the service. /etc/asterisk/init.d/ #> asterisk restart Or, use the built-in scripts... ~ # >astres.sh This is Linux, after all. A native Multi-user/muti-tasking operating system. Christopher Kovacs <w0anm73(a)gmail.com> wrote: >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

1 0

Re: [App_rpt-users] EchoLink issue
by wade 29 Dec '13

29 Dec '13

The ports are forwarding to the correct IP address. There is only one connection per location for echolink. All was working properly the first day, then the second day came and no inbound connections are possible. We can also no longer get in from our Android phones. Thi is the message my friend gets. ERROR [2306] chan_echolink.c: connect{} failed to connect to the echolink server server2.echolink.org Hope this can help diagnose what going on here.. Wade KC0MLT On 12/22/2013 2:46 PM, mike(a)midnighteng.com wrote: > > one thing to check... > incoming and outgoing routes in your router udp ports for echolink and > allstar > > then know that > > echolink only allows one connection per ip address. > > Hope that leads you somewhere if you have not found it. > > ...mike/kb8jnm > > > -------- Original Message -------- > Subject: [App_rpt-users] EchoLink issue > From: wade <wadeo(a)charter.net <mailto:wadeo@charter.net>> > Date: Sun, December 22, 2013 3:39 pm > To: App_rpt-users(a)ohnosec.org <mailto:App_rpt-users@ohnosec.org> > > Hello all, > > I recently helped a friend here in town to setup his first AllStar > node. > After getting everything up and running including the echolink > part the > next day it stopped allowing incoming connections. After doing some > investigation mine has also stopped allowing incoming connections. > Both > of ours can connect out from our nodes but no one can connect in. > On my > node it comeback with a simple time out message, on his node it comes > back with unauthorized. Has anyone had this issue before and if so > what > was the fix? > > Our routers have all the appropriate port forwarding settings in them > and have since the echolink on windows days. This is just a very > strange > occurrence to me that both of us have this problem and get two > different > messages back to other users. Any help would be greatly appreciated! > > Thanks > Wade > KC0MLT > > AllStar node 28757 > Echolink node number 223846 > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org <mailto:App_rpt-users@ohnosec.org> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >

5 6

Re: [App_rpt-users] Latitude / Longitude
by tom 28 Dec '13

28 Dec '13

I would be happy to be able to enter lat/Long numerically (if the web map is a problem). TRA

2 1

lat-lon map error
by Steve Denbow 28 Dec '13

28 Dec '13

When loading the map from Google Chrome I get an "insecure content" error. I can override the error by clicking on the "Shield" icon at the right of the url box. The actual error relates to Java and this is what it is reporting... [blocked] The page at https://allstarlink.org/portal/select_location.php?Config_ID=14C0G6E5WSV3EF… insecure content from http://maps.google.com/maps?file=api&v=2&key=ABQIAAAAcgRRwn-Z4eZbrK8vV_Ax4B…. Uncaught ReferenceError: GMap is not defined select_location.php:42<https://allstarlink.org/portal/select_location.php?Config_ID=14C0G6E5WSV3EF…> Once I get the map to display and zoom to the correct location and click the map, this is what Java is reporting... The page at https://allstarlink.org/portal/select_location.php?Config_ID=14C0G6E5WSV3EF… insecure content from http://maps.gstatic.com/mapfiles/openhand_8_8.cur. Perhaps the webmaster could use the information to correct the error. It appears to be related to SSL and API issues. Hopefully it is corrected soon. Thanks and good luck! -- Steve Denbow | KD8BIW Ohio 220 Group (419)606-5774 Mobile kd8biw(a)gmail.com www.kd8biw.com

1 0

Re: [App_rpt-users] Latitude/longitude
by zeppelin.1＠netzero.com 28 Dec '13

28 Dec '13

Pointless; the TAB key should work by default, in this case, it skips the Latitude /Longitude boxes :( Anton/ kc2rqr Node 29103 ---------- Original Message ---------- From: app_rpt-users-request(a)ohnosec.org To: app_rpt-users(a)ohnosec.org Subject: App_rpt-users Digest, Vol 58, Issue 84 Date: Sat, 28 Dec 2013 09:48:12 -0500 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. lat-lon map (41.2 Jim) 2. Re: lat-lon map (Chuck Henderson) 3. Re: Latitude / Longitude (tom) 4. Re: Latitude/longitude (zeppelin.1(a)netzero.com) ---------------------------------------------------------------------- Message: 1 Date: Fri, 27 Dec 2013 23:47:33 -0700 From: "41.2 Jim" <41.2jim(a)gmail.com> To: Allstar app_rpt-users Group <App_rpt-users(a)ohnosec.org> Subject: [App_rpt-users] lat-lon map Message-ID: <CACXxdpFuRCESMoHj4aL2miuXV=m4pNBoQ2YSSzDd9_LWEAaT4A(a)mail.gmail.com> Content-Type: text/plain; charset="iso-8859-1" I found that if you select display all content not just secure content the window with the map comes right up in Internet Explorer Jim Frederick KF6QBW 446.600- 100.0 PL Repeater AllStar Node # 28839 Skype = jim41.2

1 0