September 2012 - App_rpt-users

Aprs beacon rate
by ki6ies.tasma＠gmail.com 10 Sep '12

10 Sep '12

Where can i modify the beacon rate? I couldn't find it in gps.conf. I noticed on aprs.fi my station is beaconing at a rate of 105 times an hour for a fixed station, no gps attached. Thanks. Ian Ki6ies Sent from my Verizon Wireless 4G LTE DROID

2 1

Megan
by Edward talaro Talaro 09 Sep '12

09 Sep '12

On the CLI screen i notice 3 days ago i seen this "Megan" SIP is this normal. Is this Megans Law ? Thanks NH6WT Ed

2 1

Re: [App_rpt-users] App_rpt-users Digest, Vol 43, Issue 15
by Keith 08 Sep '12

08 Sep '12

Disconnection update I would like if possible for the node to say "Disconnecting from node XXXX, Or simple you are now disconnected". I normally send *51 to disconnect and I hear "beep beep" Also on time outs from a the Win system it just goes silent on disconnection so when time out kicks in it would be appreciated to have "Time Out " and at least I would know to re-connect Many thanks if a Asterisk bod can help Regards Keith -----Original Message----- From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of app_rpt-users-request(a)ohnosec.org Sent: 08 September 2012 17:00 To: app_rpt-users(a)ohnosec.org Subject: App_rpt-users Digest, Vol 43, Issue 15 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: pickle problem after upgrade (George Csahanin) 2. Re: Slow green led flashing on uri? (Anthony Percy) 3. Re: Slow green led flashing on uri? (Ken) 4. Remote help (Keith) 5. Re: Remote help (Jeffrey S. Carrier) ---------------------------------------------------------------------- Message: 1 Date: Fri, 7 Sep 2012 12:08:31 -0400 From: "George Csahanin" <george(a)dyb.com> To: "George Csahanin" <george(a)dyb.com>, <app_rpt-users(a)ohnosec.org> Subject: Re: [App_rpt-users] pickle problem after upgrade Message-ID: <983158B7D9BD46078E7CF330B933AE02@Goofy12> Content-Type: text/plain; format=flowed; charset="iso-8859-1"; reply-type=original Upgraded pickle last night, got this message repeating then asterisk dies off, went back to old sources, same thing. My brain is way too foggy with family issues here, can someone point to what I may have wrong, I just can't think too clearly. GeorgeC W2DB 2360 Connected to Asterisk currently running on nat (pid = 29110) [Sep 7 12:25:08] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance1 [Sep 7 12:25:08] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance1 [Sep 7 12:25:08] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance2 [Sep 7 12:25:08] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance2 [Sep 7 12:25:08] WARNING[29163]: channel.c:3051 ast_request: No channel type registered for 'Voter' [Sep 7 12:25:08] ERROR[29163]: app_radbridge.c:289 radbridge: radbridge:Sorry unable to obtain channel [Sep 7 12:25:08] WARNING[29164]: channel.c:3051 ast_request: No channel type registered for 'Voter' [Sep 7 12:25:08] ERROR[29164]: app_radbridge.c:289 radbridge: radbridge:Sorry unable to obtain channel [Sep 7 12:25:10] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance1 [Sep 7 12:25:10] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance1 I figured it out, I recompiled just from the asterisk directory, not from astsrc...all seems fine now GeorgeC ------------------------------ Message: 2 Date: Sat, 8 Sep 2012 21:36:51 +1000 From: Anthony Percy <anthcp(a)gmail.com> To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> Subject: Re: [App_rpt-users] Slow green led flashing on uri? Message-ID: <CA+rLymFntc7ZVMXG24iUJSTJ_4gEECOtb1iNNZpqensgWi5P=Q(a)mail.gmail.com> Content-Type: text/plain; charset=ISO-8859-1 Hi all, The plot thickens.... I need to explain what I mean by the flashing green LED on the C-Media based URI... Normally when it is connected to our main repeater allstar PC and working, it flashes at about once a second... However on the new ASUS mobo Allstar ACID build it only flashes about once every 2-3 seconds once asterisk has started... As you have guessed it does not pass repeater audio in this state. But it did once when it was unplugged and then plugged in, it flashed at once a second and the repeater audio worked on the new ASUS mobo. Has anyone had a similar experience??? Its looking more like to me that it is a problem with the latest ACID install and the new ASUS i3 motherboard we are using.... Whats strange is there are no errors in the message logs ( system and asterisk) or when you debug rpt in the asterisk console... The other symptom is sometimes when you plug or unplug the URI in, it hangs the PC!!! Could some explain why the URI flashes at once a second when it is operational and under what condition it would flash slower??? Regards Anthony VK2ACP On Mon, Sep 3, 2012 at 1:04 PM, Anthony Percy <anthcp(a)gmail.com> wrote: > Hi all, > Tried to make a backup of an allstar server onto a new i3 Asus mobo. > Loaded acid install and works apart from onboard netcard which was fixed by a new driver. > However with the backup config files loaded all we get is hum when we plugged on the repeater uri. We thought it was a ground loop problem untill after a reboot it all worked, audio on the repeater was fine!!! On reboot we were back to hum... Someone then noticed the uri green led was flashing slower than when it was working ok...any ideas???? > > Regards > > VK2ACP ------------------------------ Message: 3 Date: Sat, 8 Sep 2012 09:52:17 -0400 From: "Ken" <ke2n(a)cs.com> To: "'Anthony Percy'" <anthcp(a)gmail.com>, <app_rpt-users(a)ohnosec.org> Subject: Re: [App_rpt-users] Slow green led flashing on uri? Message-ID: <003501cd8dc9$292b7830$7b826890$(a)cs.com> Content-Type: text/plain; charset="us-ascii" My understanding is that the USB protocol requires 3 (re)tries on error. If you get the "slow blink" your USB comms are not working. Or they are working and returning all garbage. Ken PS: On my 3 systems the basic blink rate is faster than 1/second - more like 3-4/second > -----Original Message----- > From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users- > bounces(a)ohnosec.org] On Behalf Of Anthony Percy > Sent: Saturday, September 08, 2012 7:37 AM > To: app_rpt-users(a)ohnosec.org > Subject: Re: [App_rpt-users] Slow green led flashing on uri? > > Hi all, > The plot thickens.... I need to explain what I mean by the flashing > green LED > on the C-Media based URI... Normally when it is connected to our main > repeater allstar PC and working, it flashes at about once a second... However > on the new ASUS mobo Allstar ACID build it only flashes about once > every 2-3 > seconds once asterisk has started... As you have guessed it does not > pass repeater audio in this state. But it did once when it was > unplugged and then > plugged in, it flashed at once a second and the repeater audio worked > on the > new ASUS mobo. > > Has anyone had a similar experience??? > Its looking more like to me that it is a problem with the latest ACID install and > the new ASUS i3 motherboard we are using.... > Whats strange is there are no errors in the message logs ( system and > asterisk) or when you debug rpt in the asterisk console... > The other symptom is sometimes when you plug or unplug the URI in, it > hangs the PC!!! > > Could some explain why the URI flashes at once a second when it is > operational and under what condition it would flash slower??? > > Regards > > Anthony VK2ACP > > > > > On Mon, Sep 3, 2012 at 1:04 PM, Anthony Percy <anthcp(a)gmail.com> wrote: > > Hi all, > > Tried to make a backup of an allstar server onto a new i3 Asus mobo. > > Loaded acid install and works apart from onboard netcard which was > > fixed > by a new driver. > > However with the backup config files loaded all we get is hum when > > we > plugged on the repeater uri. We thought it was a ground loop problem untill > after a reboot it all worked, audio on the repeater was fine!!! On > reboot we > were back to hum... Someone then noticed the uri green led was > flashing slower than when it was working ok...any ideas???? > > > > Regards > > > > VK2ACP > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users ------------------------------ Message: 4 Date: Sat, 8 Sep 2012 15:52:25 +0100 From: "Keith" <keith(a)handscombe.co.uk> To: <app_rpt-users(a)ohnosec.org> Subject: [App_rpt-users] Remote help Message-ID: <001301cd8dd1$8f7c1f10$ae745d30$(a)co.uk> Content-Type: text/plain; charset="us-ascii" Hi All, I would like some Asterisk help adding the time on the hour and a disconnection announcement if possible. After having a read and getting advice from 2 Asterisk users I had a play and the node came to a halt all my own fault as I was in babysitting mode and I still so not understand some of the details. I have a ghost image and all back in less than a hour from bootable DVD so all working once more. If anyone has advice or can connect and help I would appreciate please Many thanks Keith NODE: 2498 ------------------------------ Message: 5 Date: Sat, 08 Sep 2012 09:15:27 -0600 From: "Jeffrey S. Carrier" <jeff.carrier(a)rmsmsecurity.com> To: <app_rpt-users(a)ohnosec.org>, <keith(a)handscombe.co.uk> Subject: Re: [App_rpt-users] Remote help Message-ID: <001a01cd8dd4$c8836c25$1e00000a(a)plantprotection.ad> Content-Type: text/plain; charset="utf-8" Keith, The time is fairly easy, what kind of disconnect announcement are you looking for. Can you explain that part? K0jsc Jeffrey S. Carrier Fire Inspector, Plant Protection (719) 561-7199 direct (719) 561-6567 fax 1612 E. Abriendo Ave. Pueblo, Colorado 81004 jeffrey.carrier(a)evrazincna.com Sent from my Android phone using TouchDown -----Original Message----- From: Keith [keith(a)handscombe.co.uk] Received: Saturday, 08 Sep 2012, 8:52am To: app_rpt-users(a)ohnosec.org [app_rpt-users(a)ohnosec.org] Subject: [App_rpt-users] Remote help Hi All, I would like some Asterisk help adding the time on the hour and a disconnection announcement if possible. After having a read and getting advice from 2 Asterisk users I had a play and the node came to a halt all my own fault as I was in babysitting mode and I still so not understand some of the details. I have a ghost image and all back in less than a hour from bootable DVD so all working once more. If anyone has advice or can connect and help I would appreciate please Many thanks Keith NODE: 2498 _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users ------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users End of App_rpt-users Digest, Vol 43, Issue 15 *********************************************

1 0

Re: [App_rpt-users] Remote help
by Jeffrey S. Carrier 08 Sep '12

08 Sep '12

Keith, The time is fairly easy, what kind of disconnect announcement are you looking for. Can you explain that part? K0jsc Jeffrey S. Carrier Fire Inspector, Plant Protection (719) 561-7199 direct (719) 561-6567 fax 1612 E. Abriendo Ave. Pueblo, Colorado 81004 jeffrey.carrier(a)evrazincna.com Sent from my Android phone using TouchDown -----Original Message----- From: Keith [keith(a)handscombe.co.uk] Received: Saturday, 08 Sep 2012, 8:52am To: app_rpt-users(a)ohnosec.org [app_rpt-users(a)ohnosec.org] Subject: [App_rpt-users] Remote help Hi All, I would like some Asterisk help adding the time on the hour and a disconnection announcement if possible. After having a read and getting advice from 2 Asterisk users I had a play and the node came to a halt all my own fault as I was in babysitting mode and I still so not understand some of the details. I have a ghost image and all back in less than a hour from bootable DVD so all working once more. If anyone has advice or can connect and help I would appreciate please Many thanks Keith NODE: 2498 _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

1 0

Remote help
by Keith 08 Sep '12

08 Sep '12

Hi All, I would like some Asterisk help adding the time on the hour and a disconnection announcement if possible. After having a read and getting advice from 2 Asterisk users I had a play and the node came to a halt all my own fault as I was in babysitting mode and I still so not understand some of the details. I have a ghost image and all back in less than a hour from bootable DVD so all working once more. If anyone has advice or can connect and help I would appreciate please Many thanks Keith NODE: 2498

1 0

Slow green led flashing on uri?
by Anthony Percy 08 Sep '12

08 Sep '12

Hi all, Tried to make a backup of an allstar server onto a new i3 Asus mobo. Loaded acid install and works apart from onboard netcard which was fixed by a new driver. However with the backup config files loaded all we get is hum when we plugged on the repeater uri. We thought it was a ground loop problem untill after a reboot it all worked, audio on the repeater was fine!!! On reboot we were back to hum... Someone then noticed the uri green led was flashing slower than when it was working ok...any ideas???? Regards VK2ACP

2 2

pickle problem after upgrade
by George Csahanin 07 Sep '12

07 Sep '12

Upgraded pickle last night, got this message repeating then asterisk dies off, went back to old sources, same thing. My brain is way too foggy with family issues here, can someone point to what I may have wrong, I just can't think too clearly. GeorgeC W2DB 2360 Connected to Asterisk currently running on nat (pid = 29110) [Sep 7 12:25:08] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance1 [Sep 7 12:25:08] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance1 [Sep 7 12:25:08] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance2 [Sep 7 12:25:08] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance2 [Sep 7 12:25:08] WARNING[29163]: channel.c:3051 ast_request: No channel type registered for 'Voter' [Sep 7 12:25:08] ERROR[29163]: app_radbridge.c:289 radbridge: radbridge:Sorry unable to obtain channel [Sep 7 12:25:08] WARNING[29164]: channel.c:3051 ast_request: No channel type registered for 'Voter' [Sep 7 12:25:08] ERROR[29164]: app_radbridge.c:289 radbridge: radbridge:Sorry unable to obtain channel [Sep 7 12:25:10] NOTICE[29115]: app_radbridge.c:599 radbridge_master: RPT thread restarted on instance1 [Sep 7 12:25:10] WARNING[29115]: app_radbridge.c:610 radbridge_master: radbridge_thread restarted on node instance1 George Csahanin Director of Engineering and Operations LIN TV Corp. Austin, TX 512-703-5396 office 512-481-1233 fax (private) 401-338-0568 cellular

1 1

Re: [App_rpt-users] limey and parallel port
by Tim Sawyer 06 Sep '12

06 Sep '12

One of the cool things about Limey Linux is that it runs 100% in RAM. So you can make changes to your config files and then restart asterisk to reload. If the changes work as expected you can then svcfg. If the changes didn't work and you really screw things up you can reboot the machine and your previous configuration will be back. In Limey Linux you restart asterisk with the command "killall asterisk". Because there a daemon that is always checking to see if asterisk is up, it will automatically restart after you kill it. As a side note; with CentOS the asterisk restart command is "service asterisk restart". -- Tim :wq On Sep 5, 2012, at 11:57 AM, KB7RSI <kb7rsi(a)gmail.com> wrote: > Ahhh. Ok I will do that. I've always just saved the file. That's probably why I've always had problems with Limey in the past. Brought it up before but that has never been mentioned to me. Thanks and I will update you with my progress. > > Harold > > Sent from a smartphone. Owner does make typo's for sure. > On Sep 5, 2012 7:13 AM, "Tim Sawyer" <tim.sawyer(a)me.com> wrote: > > > > Are you saving the configuration after you make changes? Limey Linux loads everything from the CF card into ram when it boots. Any changes you make need to be saved to the CF card with the command svcfg. > > -- > > Tim > > :wq > > > > On Sep 4, 2012, at 9:53 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > > > > Well, one thing I did notice that is contributing to my issue is, > > > every time i reboot my system, I end up with both usbradio.conf and > > > simpleusb.conf files. Also, If I delete these files and reboot, they > > > re-appear, and if I do modify either one of those files and reboot, > > > they end up being overwritten loosing any changes that i have made. > > > Not really sure of what happening here. > > > > > > Thanks > > > > > > Harold > > > > > > On Tue, Sep 4, 2012 at 8:57 PM, Tim Sawyer <tim.sawyer(a)me.com> wrote: > > >> It works on Limey Linux. We're using it in a number of nodes. Here's the > > >> simpleusb.conf from one of my nodes: > > >> > > >> [general] > > >> > > >> [usb] > > >> > > >> pp2 = ptt > > >> pp3= out0 > > >> pp10 = cor > > >> > > >> eeprom=0 > > >> > > >> hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using > > >> ; the instructions from usbfob.pdf. Use a setting of > > >> ; 1 is for Dingotel/Sph interfaces. > > >> > > >> rxboost=0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed > > >> ; Set to 1 for additonal gain if using a low-level receiver output > > >> > > >> ;carrierfrom=ppinvert ; no,usb,usbinvert > > >> carrierfrom=pp ; no,usb,usbinvert > > >> ; no - no carrier detection at all > > >> ; usb - from the COR line on the modified USB sound fob > > >> ; usbinvert - from the inverted COR line on the modified USB sound fob > > >> > > >> ctcssfrom=no ; no,usb,usbinvert > > >> ; no - CTCSS decoding, system will be carrier squelch > > >> ; usb - CTCSS decoding using input from USB FOB > > >> ; usbinvert - from the inverted CTCSS line on the modified USB sound fob > > >> > > >> txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice > > >> ; no - Do not output anything > > >> ; voice - output voice only > > >> > > >> txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice > > >> ; See txmixa above. > > >> > > >> invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit > > >> ; This is the collector lead of the 2n4401 on the modified > > >> ; usb sound fob. > > >> ; please refer to the howto for the procedure to do this. > > >> > > >> duplex=1 ; Full Duplex > > >> plfilter=yes > > >> > > >> -- > > >> Tim > > >> :wq > > >> > > >> On Sep 4, 2012, at 7:14 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Also, im not sure that this applies to limey linux. > > >> > > >> Thanks > > >> > > >> On Tue, Sep 4, 2012 at 7:13 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Ok thanks for that info. > > >> I guess limey does not totally support my via motherboard. > > >> It will not address my parallel port for some reason. > > >> > > >> Thanks again. > > >> > > >> Harold > > >> > > >> On Tue, Sep 4, 2012 at 5:46 PM, Tim Sawyer <tim.sawyer(a)me.com> wrote: > > >> > > >> http://ohnosec.org/drupal/node/177 > > >> -- > > >> Tim > > >> :wq > > >> > > >> On Sep 4, 2012, at 5:14 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Hello all. > > >> Does anyone know what the parallel port is called in dev folder in > > >> limey linux if its even available? > > >> Im trying to use my parallel port for keying and COR for my radio. > > >> > > >> Thanks > > >> > > >> Harold > > >> _______________________________________________ > > >> App_rpt-users mailing list > > >> App_rpt-users(a)ohnosec.org > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >> > > >> > > >> > > >> > > >> _______________________________________________ > > >> App_rpt-users mailing list > > >> App_rpt-users(a)ohnosec.org > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >> > > >

2 1

CLI Echolink Call Sign Logging
by Kent Ochs 06 Sep '12

06 Sep '12

This problem appears to be related to the following code change where the ast_log function is no longer being called at connection time when Verbosity > 3 Chan_Echolink (Rev 971) ast_log(LOG_NOTICE, "new CALL=%s,ip=%s,name=%s\n", Chan_Echolink (Rev 1201) if (option_verbose > 3) ast_verbose(VERBOSE_PREFIX_3 "new CALL=%s,ip=%s,name=%s\n", This has been logged as Mantis Issue 76. Thanks. Kent W9KAO

4 5

Re: [App_rpt-users] limey and parallel port
by Tim Sawyer 05 Sep '12

05 Sep '12

Harold, On a not related subject... It's a good practice to reply all. That way others can learn, not only from the real-time emails but also the Google searchable archives. -- Tim :wq On Sep 5, 2012, at 11:57 AM, KB7RSI <kb7rsi(a)gmail.com> wrote: > Ahhh. Ok I will do that. I've always just saved the file. That's probably why I've always had problems with Limey in the past. Brought it up before but that has never been mentioned to me. Thanks and I will update you with my progress. > > Harold > > Sent from a smartphone. Owner does make typo's for sure. > On Sep 5, 2012 7:13 AM, "Tim Sawyer" <tim.sawyer(a)me.com> wrote: > > > > Are you saving the configuration after you make changes? Limey Linux loads everything from the CF card into ram when it boots. Any changes you make need to be saved to the CF card with the command svcfg. > > -- > > Tim > > :wq > > > > On Sep 4, 2012, at 9:53 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > > > > Well, one thing I did notice that is contributing to my issue is, > > > every time i reboot my system, I end up with both usbradio.conf and > > > simpleusb.conf files. Also, If I delete these files and reboot, they > > > re-appear, and if I do modify either one of those files and reboot, > > > they end up being overwritten loosing any changes that i have made. > > > Not really sure of what happening here. > > > > > > Thanks > > > > > > Harold > > > > > > On Tue, Sep 4, 2012 at 8:57 PM, Tim Sawyer <tim.sawyer(a)me.com> wrote: > > >> It works on Limey Linux. We're using it in a number of nodes. Here's the > > >> simpleusb.conf from one of my nodes: > > >> > > >> [general] > > >> > > >> [usb] > > >> > > >> pp2 = ptt > > >> pp3= out0 > > >> pp10 = cor > > >> > > >> eeprom=0 > > >> > > >> hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using > > >> ; the instructions from usbfob.pdf. Use a setting of > > >> ; 1 is for Dingotel/Sph interfaces. > > >> > > >> rxboost=0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed > > >> ; Set to 1 for additonal gain if using a low-level receiver output > > >> > > >> ;carrierfrom=ppinvert ; no,usb,usbinvert > > >> carrierfrom=pp ; no,usb,usbinvert > > >> ; no - no carrier detection at all > > >> ; usb - from the COR line on the modified USB sound fob > > >> ; usbinvert - from the inverted COR line on the modified USB sound fob > > >> > > >> ctcssfrom=no ; no,usb,usbinvert > > >> ; no - CTCSS decoding, system will be carrier squelch > > >> ; usb - CTCSS decoding using input from USB FOB > > >> ; usbinvert - from the inverted CTCSS line on the modified USB sound fob > > >> > > >> txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice > > >> ; no - Do not output anything > > >> ; voice - output voice only > > >> > > >> txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice > > >> ; See txmixa above. > > >> > > >> invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit > > >> ; This is the collector lead of the 2n4401 on the modified > > >> ; usb sound fob. > > >> ; please refer to the howto for the procedure to do this. > > >> > > >> duplex=1 ; Full Duplex > > >> plfilter=yes > > >> > > >> -- > > >> Tim > > >> :wq > > >> > > >> On Sep 4, 2012, at 7:14 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Also, im not sure that this applies to limey linux. > > >> > > >> Thanks > > >> > > >> On Tue, Sep 4, 2012 at 7:13 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Ok thanks for that info. > > >> I guess limey does not totally support my via motherboard. > > >> It will not address my parallel port for some reason. > > >> > > >> Thanks again. > > >> > > >> Harold > > >> > > >> On Tue, Sep 4, 2012 at 5:46 PM, Tim Sawyer <tim.sawyer(a)me.com> wrote: > > >> > > >> http://ohnosec.org/drupal/node/177 > > >> -- > > >> Tim > > >> :wq > > >> > > >> On Sep 4, 2012, at 5:14 PM, KB7RSI <kb7rsi(a)gmail.com> wrote: > > >> > > >> Hello all. > > >> Does anyone know what the parallel port is called in dev folder in > > >> limey linux if its even available? > > >> Im trying to use my parallel port for keying and COR for my radio. > > >> > > >> Thanks > > >> > > >> Harold > > >> _______________________________________________ > > >> App_rpt-users mailing list > > >> App_rpt-users(a)ohnosec.org > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >> > > >> > > >> > > >> > > >> _______________________________________________ > > >> App_rpt-users mailing list > > >> App_rpt-users(a)ohnosec.org > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >> > > >

1 0