January 2015 - App_rpt-users - lists.keekles.org

Re: [App_rpt-users] Node Status not showing...
by Jah Rastafari 13 Jan '15

13 Jan '15

Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air... Bob/KK6RQ On Sun, Jan 11, 2015 at 8:28 PM, <mike(a)midnighteng.com> wrote: > > > You could be having some problems with internet host (especially if it > is comcast). > Probably temporary, don't go changing your settings over it just yet. > Give it a few days and reboots (computer and router) to see how it pans > out. > > > ...mike/kb8jnm > > > -------- Original Message -------- > > Subject: Re: [App_rpt-users] Node Status not showing... > > From: Jah Rastafari <nuhtrue(a)gmail.com> > > Date: Sun, January 11, 2015 9:20 pm > > To: mike(a)midnighteng.com, "app_rpt-users(a)ohnosec.org" > > <app_rpt-users(a)ohnosec.org> > > > > > > I went back right after reading your reply (several hours after my > original > > post) and it in fact came up the way it should. But then 5 minutes > > later it went back to saying I wasn't connected. I'm not sure what it > means > > but I can say I've never seen it behave like this before. > > > > On Sun, Jan 11, 2015 at 4:56 PM, <mike(a)midnighteng.com> wrote: > > > > > > > > > > > > > > Not sure but.... > > > > > > I think you are only suffering from a delay of the update to the list. > > > > > > Try waiting for a short while (up to 30min) and look again. > > > Others have said it takes that long sometimes but I have only witnessed > > > about 5-6min. > > > > > > Guess it depends on how busy the server is. > > > > > > > > > ...mike/kb8jnm > > > > > > > -------- Original Message -------- > > > > Subject: [App_rpt-users] Node Status not showing... > > > > From: Jah Rastafari <nuhtrue(a)gmail.com> > > > > Date: Sun, January 11, 2015 5:29 pm > > > > To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > > > > > > > > > > > > Forgive me if this has already been discussed and I missed it, but I > just > > > > noticed recently that although I was connected to a number of other > > > > nodes/repeaters, the 'Node Status' selection on the Allstar site > says I'm > > > > not connected to anything. My node(s) show up properly in the > available > > > > node list and everything else is as it should be. The Web Transceiver > > > works > > > > properly also and I haven't changed anything recently. Am I missing > > > > something? > > > > > > > > Bob/ KK6RQ<hr>_______________________________________________ > > > > App_rpt-users mailing list > > > > App_rpt-users(a)ohnosec.org > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > > > To unsubscribe from this list please visit > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > down > > > to the bottom of the page. Enter your email address and press the > > > "Unsubscribe or edit options button" > > > > You do not need a password to unsubscribe, you can do it via email > > > confirmation. If you have trouble unsubscribing, please send a message > to > > > the list detailing the problem. > > > >

4 5

Quad PCI cards?
by Bryan Fields 12 Jan '15

12 Jan '15

I'm looking for one or maybe two of these for a new install. Please unicast me if you have one and want to get rid of it. 73's W9CR -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Re: [App_rpt-users] Node Status not showing...
by Jah Rastafari 12 Jan '15

12 Jan '15

I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before. On Sun, Jan 11, 2015 at 4:56 PM, <mike(a)midnighteng.com> wrote: > > > > Not sure but.... > > I think you are only suffering from a delay of the update to the list. > > Try waiting for a short while (up to 30min) and look again. > Others have said it takes that long sometimes but I have only witnessed > about 5-6min. > > Guess it depends on how busy the server is. > > > ...mike/kb8jnm > > > -------- Original Message -------- > > Subject: [App_rpt-users] Node Status not showing... > > From: Jah Rastafari <nuhtrue(a)gmail.com> > > Date: Sun, January 11, 2015 5:29 pm > > To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > > > > > > Forgive me if this has already been discussed and I missed it, but I just > > noticed recently that although I was connected to a number of other > > nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm > > not connected to anything. My node(s) show up properly in the available > > node list and everything else is as it should be. The Web Transceiver > works > > properly also and I haven't changed anything recently. Am I missing > > something? > > > > Bob/ KK6RQ<hr>_______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. >

1 0

what am i missing.. Progress
by Mike Lussier 12 Jan '15

12 Jan '15

It seems I'm making some head way. The last testing before I called it quits tonight I was getting "The number you dialled is not in service followed by busy signal. some times just the busy signal. I have enabled "DTMF" on the debug logs. It appears that the system doesn't like all the key pad numbers on all of my radios. different ones certain keys don't show up in the log. More work later this week in the evenings. Thank you for your help. Mike -- *"We * *Message: 1 Date: Sun, 11 Jan 2015 13:07:57 -0500 From: Doug Crompton <doug(a)crompton.com <doug(a)crompton.com>> To: Mike Lussier <mike.lussier(a)gmail.com <mike.lussier(a)gmail.com>> Cc: "app_rpt-users(a)ohnosec.org <app_rpt-users(a)ohnosec.org>" <app_rpt-users(a)ohnosec.org <app_rpt-users(a)ohnosec.org>> Subject: Re: [App_rpt-users] what am I missing ? Message-ID: <BLU172-* W3882F8780314544B8F9040BA420(a)phx.gbl> Content-Type: text/plain; charset="iso-8859-1" Mike, When you do this you should have the client open and watch the log. Much info can be gained there. 73 Doug WA3DSP http://www.crompton.com/hamradio Date: Sun, 11 Jan 2015 10:53:33 -0500 From: mike.lussier(a)gmail.com To: app_rpt-users(a)ohnosec.org Subject: [App_rpt-users] what am I missing ? I stepped away from this last night. I was getting frustrated. What I'm trying to do. dial via DTMF from radio and route the call to the local PBX in my home. I already have a Trunk established between the PBX and the BBB Node. I can place calls directly to the node, TX & RX. When I initiate a call to the phone from my HT the only response I get back is a courtesy tone. I have tried all of these combinations. *6 6001 # *6 6001 6 6001 # 6 6001 There is an IAX2 trunk from the PBX to the BBB AllStar node running 1.2.1. I can place a call to the node from the phone. I can transmit & receive. on the BBB node : I setup my test phone extension 6001 in iax.cnf file on the node the dial command is different dial=iax/6001 [6001] deny=0.0.0.0/0.0.0.0 username=6001 secret=xxxx dtmfmode=rfc2833 canreinvite=no context=radio-control host=dynamic trustrpid=yes sendrpid=no type=peer nat=no port=5060 qualify=yes qualifyfreq=60 transport=udp encryption=no callgroup=RPT pickupgroup=ALL dial=IAX6001 permit=0.0.0.0/0.0.0.0 allow=ulaw,gsm,h263 ======= rpt.conf 6=autopatchup,noct=1,farenddisconnect=1,dialtime=40000 ; Autopatch up ======= In extensions.conf the phone patch is the [RADIO] context [radio] exten => _5XXX,1,Dial(iax/${EXTEN},17); ; home phones exten => _6XXX,1,Dial(iax/${EXTEN},17); ; mesh phones *must reject the idea that every time a law is broken, society is guilty rather than the law breaker.It is time to restore the American precept that each individual is accountable for his actions." ~ Ronald Regan*

1 0

Node Status not showing...
by Jah Rastafari 11 Jan '15

11 Jan '15

Forgive me if this has already been discussed and I missed it, but I just noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something? Bob/ KK6RQ

1 0

Re: [App_rpt-users] New node number
by mike＠midnighteng.com 11 Jan '15

11 Jan '15

Create a new server if it is a new server in which you are placing new or old nodes to it (a new asterisk box) then you can create new nodes for that box and/or move old nodes to it. server/create new / name the server Then request node for that server. or request a new node for a existing server.(node/select server it is for) ...mike/kb8jnm > -------- Original Message -------- > Subject: [App_rpt-users] New node number > From: Robert Newberry <N1XBM(a)amsat.org> > Date: Sun, January 11, 2015 2:13 pm > To: app_rpt-users(a)ohnosec.org > > > Can some refresh my memory. I am in the process of setting up a BBB. I need > a new node number. > > Do I log into allstarlink.org and click node, then request node, then my > callsign? > > I'm not sure if I click that or create server? > > Thank you.<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

New node number
by Robert Newberry 11 Jan '15

11 Jan '15

Can some refresh my memory. I am in the process of setting up a BBB. I need a new node number. Do I log into allstarlink.org and click node, then request node, then my callsign? I'm not sure if I click that or create server? Thank you.

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 71, Issue 18
by mike＠midnighteng.com 11 Jan '15

11 Jan '15

Mike, Thanks for the diagram, it makes it clear almost. I assume the 6xxx extensions/devices are registering with the mesh-pbx. And 5xxx extensions/devices are registering with Home-PBX. For any two extension/devices that are registered in the same asterisk server. exten => _5XXX,1,Dial(iax/${EXTEN},17); home phones A string like above should work. You should be able to reach them via radio phone patch via radios attached to the same HOME-PBX asterisk box. To dial from a extension/device that is registared outside of home-pbx to mesh-pbx exten => _6XXX,1,Dial(iax/NAMEOFTRUNKTOUSE/${EXTEN},17); ;home-pbx dialing mesh-pbx extsions NAMEOFTRUNKTOUSE = the name of the route you created from origination to destination. You may have declared one the opposite way but you need a path going in the correct direction for the call. It is NOT automatically bi-directional but a very directional route. Obviously, you have created a route to dial into the node (named?). You just need one going in the opposite direction to get from home-pbx to the mesh=pbx. When you create that, specify it in the dial string for NAMEOFTRUNK Once you have that done, do the same in the other direction (changing dial string to reflect extensions and named trunk used) I hope that makes things clearer as to what needs to be done. I have assumed a little more about what you had completed in your set-up then I should have. If there is any confusion on my part, it would be that I don't know where the extensions are registered. The correct set-up is a matter of perspective of from where to where. I think your problem is simply, you have no trunk/route going the proper direction and it is not declared in the dial string. "You have a incoming route but not a outgoing one". Let me know how your progress and anything else you might need. ...mike/kb8jnm > -------- Original Message -------- > Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 71, Issue 18 > From: Mike Lussier <mike.lussier(a)gmail.com> > Date: Sun, January 11, 2015 12:38 pm > To: ALL STAR <app_rpt-users(a)ohnosec.org> > > > MIke > > here is a very basic diagram. Sorry Visio is on my work computer not > personal. The allstar node in on the mesh network. I have a PBX on the mesh > network. The phones on the mesh use 6xxx as the extension range. > > On the home network I have another PBX both are linked via IAX2 trunk. > Home extensions are 5xxx. > > No internet access for mesh devices except specific ports for those devices > that need access link allstarlink, phones ,aprs and a couple others.no > encryption allowed period. > Access to the home network is permited. no calls permitted to the outside > world from the mesh only the ability to ring home extensions. > > I'm looking at the files now and your last message. > > Thank you > > Mike > > On Sun, Jan 11, 2015 at 12:00 PM, <app_rpt-users-request(a)ohnosec.org> wrote: > > > Send App_rpt-users mailing list submissions to > > app_rpt-users(a)ohnosec.org > > > > To subscribe or unsubscribe via the World Wide Web, visit > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > or, via email, send a message with subject or body 'help' to > > app_rpt-users-request(a)ohnosec.org > > > > You can reach the person managing the list at > > app_rpt-users-owner(a)ohnosec.org > > > > When replying, please edit your Subject line so it is more specific > > than "Re: Contents of App_rpt-users digest..." > > > > > > Today's Topics: > > > > 1. what am I missing ? (Mike Lussier) > > 2. Re: what am I missing ? (mike(a)midnighteng.com) > > > > > > ---------------------------------------------------------------------- > > > > Message: 1 > > Date: Sun, 11 Jan 2015 10:53:33 -0500 > > From: Mike Lussier <mike.lussier(a)gmail.com> > > To: ALL STAR <app_rpt-users(a)ohnosec.org> > > Subject: [App_rpt-users] what am I missing ? > > Message-ID: > > < > > CAJ_8STk1tgh8XuMAqXgtYjrYVtHVCz54o_n_BgSSeG8K1rCWCQ(a)mail.gmail.com> > > Content-Type: text/plain; charset="utf-8" > > > > I stepped away from this last night. I was getting frustrated. > > > > What I'm trying to do. dial via DTMF from radio and route the call to the > > local PBX in my home. I already have a Trunk established between the PBX > > and the > > BBB Node. I can place calls directly to the node, TX & RX. > > > > When I initiate a call to the phone from my HT the only response I get > > back is a courtesy tone. > > > > I have tried all of these combinations. > > > > *6 6001 # > > *6 6001 > > 6 6001 # > > 6 6001 > > > > There is an IAX2 trunk from the PBX to the BBB AllStar node running 1.2.1. > > > > I can place a call to the node from the phone. I can transmit & receive. > > > > on the BBB node : > > > > I setup my test phone extension 6001 in iax.cnf file on the node the dial > > command is different dial=iax/6001 > > > > [6001] > > deny=0.0.0.0/0.0.0.0 > > username=6001 > > secret=xxxx > > dtmfmode=rfc2833 > > canreinvite=no > > context=radio-control > > host=dynamic > > trustrpid=yes > > sendrpid=no > > type=peer > > nat=no > > port=5060 > > qualify=yes > > qualifyfreq=60 > > transport=udp > > encryption=no > > callgroup=RPT > > pickupgroup=ALL > > dial=IAX6001 > > permit=0.0.0.0/0.0.0.0 > > allow=ulaw,gsm,h263 > > > > ======= > > > > rpt.conf > > > > 6=autopatchup,noct=1,farenddisconnect=1,dialtime= > > 40000 ; Autopatch > > up > > > > > > ======= > > In extensions.conf the phone patch is the [RADIO] context > > > > [radio] > > exten => _5XXX,1,Dial(iax/${EXTEN},17); ; home phones > > exten => _6XXX,1,Dial(iax/${EXTEN},17); ; mesh phones > >

1 0

what am I missing ?
by Mike Lussier 11 Jan '15

11 Jan '15

I stepped away from this last night. I was getting frustrated. What I'm trying to do. dial via DTMF from radio and route the call to the local PBX in my home. I already have a Trunk established between the PBX and the BBB Node. I can place calls directly to the node, TX & RX. When I initiate a call to the phone from my HT the only response I get back is a courtesy tone. I have tried all of these combinations. *6 6001 # *6 6001 6 6001 # 6 6001 There is an IAX2 trunk from the PBX to the BBB AllStar node running 1.2.1. I can place a call to the node from the phone. I can transmit & receive. on the BBB node : I setup my test phone extension 6001 in iax.cnf file on the node the dial command is different dial=iax/6001 [6001] deny=0.0.0.0/0.0.0.0 username=6001 secret=xxxx dtmfmode=rfc2833 canreinvite=no context=radio-control host=dynamic trustrpid=yes sendrpid=no type=peer nat=no port=5060 qualify=yes qualifyfreq=60 transport=udp encryption=no callgroup=RPT pickupgroup=ALL dial=IAX6001 permit=0.0.0.0/0.0.0.0 allow=ulaw,gsm,h263 ======= rpt.conf 6=autopatchup,noct=1,farenddisconnect=1,dialtime= 40000 ; Autopatch up ======= In extensions.conf the phone patch is the [RADIO] context [radio] exten => _5XXX,1,Dial(iax/${EXTEN},17); ; home phones exten => _6XXX,1,Dial(iax/${EXTEN},17); ; mesh phones

2 1

Re: [App_rpt-users] App_rpt-users Digest, Vol 71, Issue 18
by Mike Lussier 11 Jan '15

11 Jan '15

MIke here is a very basic diagram. Sorry Visio is on my work computer not personal. The allstar node in on the mesh network. I have a PBX on the mesh network. The phones on the mesh use 6xxx as the extension range. On the home network I have another PBX both are linked via IAX2 trunk. Home extensions are 5xxx. No internet access for mesh devices except specific ports for those devices that need access link allstarlink, phones ,aprs and a couple others.no encryption allowed period. Access to the home network is permited. no calls permitted to the outside world from the mesh only the ability to ring home extensions. I'm looking at the files now and your last message. Thank you Mike On Sun, Jan 11, 2015 at 12:00 PM, <app_rpt-users-request(a)ohnosec.org> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. what am I missing ? (Mike Lussier) > 2. Re: what am I missing ? (mike(a)midnighteng.com) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sun, 11 Jan 2015 10:53:33 -0500 > From: Mike Lussier <mike.lussier(a)gmail.com> > To: ALL STAR <app_rpt-users(a)ohnosec.org> > Subject: [App_rpt-users] what am I missing ? > Message-ID: > < > CAJ_8STk1tgh8XuMAqXgtYjrYVtHVCz54o_n_BgSSeG8K1rCWCQ(a)mail.gmail.com> > Content-Type: text/plain; charset="utf-8" > > I stepped away from this last night. I was getting frustrated. > > What I'm trying to do. dial via DTMF from radio and route the call to the > local PBX in my home. I already have a Trunk established between the PBX > and the > BBB Node. I can place calls directly to the node, TX & RX. > > When I initiate a call to the phone from my HT the only response I get > back is a courtesy tone. > > I have tried all of these combinations. > > *6 6001 # > *6 6001 > 6 6001 # > 6 6001 > > There is an IAX2 trunk from the PBX to the BBB AllStar node running 1.2.1. > > I can place a call to the node from the phone. I can transmit & receive. > > on the BBB node : > > I setup my test phone extension 6001 in iax.cnf file on the node the dial > command is different dial=iax/6001 > > [6001] > deny=0.0.0.0/0.0.0.0 > username=6001 > secret=xxxx > dtmfmode=rfc2833 > canreinvite=no > context=radio-control > host=dynamic > trustrpid=yes > sendrpid=no > type=peer > nat=no > port=5060 > qualify=yes > qualifyfreq=60 > transport=udp > encryption=no > callgroup=RPT > pickupgroup=ALL > dial=IAX6001 > permit=0.0.0.0/0.0.0.0 > allow=ulaw,gsm,h263 > > ======= > > rpt.conf > > 6=autopatchup,noct=1,farenddisconnect=1,dialtime= > 40000 ; Autopatch > up > > > ======= > In extensions.conf the phone patch is the [RADIO] context > > [radio] > exten => _5XXX,1,Dial(iax/${EXTEN},17); ; home phones > exten => _6XXX,1,Dial(iax/${EXTEN},17); ; mesh phones >

1 0