April 2014 - App_rpt-users - lists.keekles.org

Re: [App_rpt-users] URI and URIx Testing
by Bob 27 Apr '14

27 Apr '14

Most recent ACID distro from Allstarlink.org. Gigabyte C1007UN-D with 4 gig memory, and an SSD SATA drive. Built in with an IntelR Dual-core CeleronR 1007U processor (1.5 GHz) lsusb -v reports the URI and the URIx both as USB 1.1 Thanks, Bob kk6ecm _____ From: Chris Andrist [mailto:chris@yeahmon.net] Sent: Friday, April 25, 2014 6:02 PM To: Bob Subject: Re: [App_rpt-users] URI and URIx Testing Bob, Tell us about the computer you are running this on and what Distro you are using? Just as an FYI. ACID runs best on Pentium 4 computers and slower. -- Regards, Chris Andrist, KC7WSU On Apr 25, 2014, at 6:59 PM, "Bob" <kk6ecm(a)gmail.com> wrote: I'm at a loss... looking for ideas on how to proceed... Still attempting to get our repeater working... rebuilt the computer that crashed, and it works well... Getting strange results when connecting the URI back to the radio (can't find anything wrong there). The fact I can't seem to get a URI, or URIx working with my computer suggests a possible issue with my setup. I have some inputs from folks for changes in the usbradio, or simpleusb which I'd like to check, but need to confirm the URI is working correctly, so I'm not chasing hardware issues by looking at software. I tested my URI using the loopback diagram and uridiag; it passes all the digital, and fails all the analog. I procured a URIx for replacement, and built up the loopback connector for it and tested, same results. I've checked and rechecked my wiring of the loopback connector. The URIx uses two 1k resistors and two extra jumpers than the URI (see below), and the URI two 10k resistors per DMK folks. (There is a confirmed error in the uridiag listed connections). I did not connect the URIx 12 and 20 (Blk and Wht) leads, nor the power supply to activate the 2x amplifier (pins 13 & 25), which I am not using. I'm told the correct connections are as shown below from the URI-FAQ.pdf, with change of 1K for 10K for URIx per DMK, and comparing with the URIx test fixture. Assuming the URIx was good from the factory, and all I did was connect it up to the loopback and computer, turn on the computer with ACID # service asterisk stop # uridiag URIDiag, diagnostic program for the DMK Engineering URI USB Radio Interface, version 0.8, 04/26/11 Found CM119 USB Radio Interface at 001/003 . . . Enter your selection:t Testing digital I/O (PTT,COR,TONE and GPIO).... Digital I/O passed!! Testing Analog at 204 (and 700) Hz... Analog level on left channel for 204.0 Hz (0.0) is out of range!! . . . 24 Error(s) found during test(s)!!!! URI Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 10K Resistor between Pins 21 and 22 10K Resistor between Pins 21 and 23 URIx Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 1K Resistor between Pins 21 and 22 1K Resistor between Pins 21 and 23 Pin 5 to Pin 10 Pin 6 to Pin 11 sigh! Thanks, Bob kk6ecm _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

4 6

URI and URIx Testing
by Bob 26 Apr '14

26 Apr '14

I'm at a loss... looking for ideas on how to proceed... Still attempting to get our repeater working... rebuilt the computer that crashed, and it works well... Getting strange results when connecting the URI back to the radio (can't find anything wrong there). The fact I can't seem to get a URI, or URIx working with my computer suggests a possible issue with my setup. I have some inputs from folks for changes in the usbradio, or simpleusb which I'd like to check, but need to confirm the URI is working correctly, so I'm not chasing hardware issues by looking at software. I tested my URI using the loopback diagram and uridiag; it passes all the digital, and fails all the analog. I procured a URIx for replacement, and built up the loopback connector for it and tested, same results. I've checked and rechecked my wiring of the loopback connector. The URIx uses two 1k resistors and two extra jumpers than the URI (see below), and the URI two 10k resistors per DMK folks. (There is a confirmed error in the uridiag listed connections). I did not connect the URIx 12 and 20 (Blk and Wht) leads, nor the power supply to activate the 2x amplifier (pins 13 & 25), which I am not using. I'm told the correct connections are as shown below from the URI-FAQ.pdf, with change of 1K for 10K for URIx per DMK, and comparing with the URIx test fixture. Assuming the URIx was good from the factory, and all I did was connect it up to the loopback and computer, turn on the computer with ACID # service asterisk stop # uridiag URIDiag, diagnostic program for the DMK Engineering URI USB Radio Interface, version 0.8, 04/26/11 Found CM119 USB Radio Interface at 001/003 . . . Enter your selection:t Testing digital I/O (PTT,COR,TONE and GPIO).... Digital I/O passed!! Testing Analog at 204 (and 700) Hz... Analog level on left channel for 204.0 Hz (0.0) is out of range!! . . . 24 Error(s) found during test(s)!!!! URI Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 10K Resistor between Pins 21 and 22 10K Resistor between Pins 21 and 23 URIx Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 1K Resistor between Pins 21 and 22 1K Resistor between Pins 21 and 23 Pin 5 to Pin 10 Pin 6 to Pin 11 sigh! Thanks, Bob kk6ecm

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 62, Issue 66
by Malcolm Good 26 Apr '14

26 Apr '14

Hi Tim This development is great. I wasn't expecting this for months. I look forward to implementing when I get back home. Once again thanks for making avaliable you code. Mal sent from my Samsung Note On 26/04/2014 12:00 AM, <app_rpt-users-request(a)ohnosec.org> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > Today's Topics: > > 1. Allmon Control Panel (Tim Sawyer) > > > ---------- Forwarded message ---------- > From: Tim Sawyer <tim.sawyer(a)mac.com> > To: Allstar Users <app_rpt-users(a)ohnosec.org> > Cc: > Date: Thu, 24 Apr 2014 17:02:08 -0700 > Subject: [App_rpt-users] Allmon Control Panel > Allmon can now do pretty much anything that can be done at the Asterisk > CLI giving you complete web based control of your nodes. > > The Allmon Control Panel is a popup window which allows selected commands > to be issued through the Asterisk Manager Interface. The command selection > is configured with an ini file allowing the Allmon admin set up virtually > any AMI command. The included sample ini show you just some of the things > you can do. > > Users must login to see the new Control Panel button. If more than one > node is display, select a node from the drop down and them press Control > Panel. > > Please grab the latest Allmon at my gtihub at > https://github.com/tsawyer/allmon/tree/allmon2 > > Enjoy, > — > Tim WD6AWP > :wq > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >

1 0

Back from the hospital
by Jim Duuuude 25 Apr '14

25 Apr '14

Well, once again, I found myself needing to go to the hospital on Sunday. I am back now, and feeling much better. That is why I was not responding to emails. Jim

3 2

How to stream live audio from URI to broadcast software.
by Loren Tedford 24 Apr '14

24 Apr '14

Hello my name is Loren I would like to set up a live audio stream from my repeater to broadcastify if anyone has any suggestions on how or what i should do this would be appreciated. I would much rather if I could just take the audio from the repeater its self rather than setting up a secondary scanner then reroute it back to broadcastify.. Using Acid Linux Distro all normal install.. URI connected to two GM300s etc.. Any suggestions on this idea and if you have done this before please let me know how ya did this or what i need to do to get started 73's for now. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Email: loren(a)lorentedford.com http://www.lorentedford.com

2 1

Allmon Version 2 Released
by Tim Sawyer 23 Apr '14

23 Apr '14

The first thing you should know is that Allmon 2 will NOT work with Internet Explorer. Every other modern browser on earth works fine but for some reason Microsoft is not on the HTML 5 SSE bandwagon. Keep the old version if you need IE support. The old version is still on Github. Many changes in this version (see the README). Main change is it’s faster and puts less load on your server and on Asterisk. Also, clicking on the links (ie the old X for disconnect, etc) actually work the first time you click them… imagine that! Here the link https://github.com/tsawyer/allmon/tree/allmon2 Enjoy, -- Tim :wq

1 2

RTCM board assembling. Problems
by Mihhail Jakovlev 23 Apr '14

23 Apr '14

Hi all, I have 4 RTCM boards assembled, but only one fully working :) Could any help with finding faults in other boards? I have test node 2300 configured and SIP phone for connecting with test node. Board2: Not work audio from receiver to server (to phone). From phone to radio is ok. In offline mode audio from receiver to transmitter is ok. Radio unkey courtesy tone in phone is ok. What is faulty? In offline mode audio comes from receiver to CPU, and from CPU to transmitter. If offline mode working, audio parts is ok. Board3: cannot write own parameters to eprom. All changes in console menu erased after repowering. Eprom ic 25080 replaced, not result. Voltages and waveforms on eprom ic pins same as in board2. Board4: If power up, green status led flash twice, console show text menu, after this starts red tx led for 1s and board restarts. Ideas? Thanks! Regards, Mihhail Jakovlev

1 0

Added a second node to my server Status problem
by W2YMM 23 Apr '14

23 Apr '14

Hi, I have a second node I connected to my server today. My original node was 28183 and all was working fine. I added 29973 today. Both nodes are using URI Interfaces. I seem to have lost my ONLINE Status on the http://stats.allstarlink.org/ webpage for my First Node. (28183) 29973 seems to be ok. http://stats.allstarlink.org/nodeinfo.cgi?node=29973 I get the Node is no longer in the database message at http://stats.allstarlink.org/nodeinfo.cgi?node=28183 although I do show up GREEN on https://allstarlink.org/nodelist.php The only thing I did was add the second node to my server, and edit the extensions.conf, iax.conf, rpt.conf, usbradio.conf files. Any help would be greatly appreciated. The nodes appear to be working correctly, just 28183 no longer showing up on the status page. Bob W2YMM Robert Prybyzerski Jr W2YMM 631-960-1051 http://www.w2ymm.com

7 9

MAC Mini For AllStar Server?
by Chris Hill - K7AZ 23 Apr '14

23 Apr '14

I posted this earlier but did not get a response. Can anyone tell me if a MAC Mini can be used to make an AllStar server? Thank you, Chris K7AZ

4 3

Adafruit has Blacks!
by Doug Crompton 22 Apr '14

22 Apr '14

I just got notification and ordered another one. They have 78 in stock 3PM EST. http://www.adafruit.com/products/1278 You should order a case also - PRODUCT ID: 1555 $9.95 73 Doug WA3DSP http://www.crompton.com/hamradio

1 0