- App_rpt-users - lists.keekles.org

Re: [App_rpt-users] RX Input Adjust Failed
by kk6ecm 24 May '16

24 May '16

I discovered app_rpt does not like ctcssfrom=no. Why? (I'm using DIAL). What am I missing? Thanks, Bob kk6ecm 73 -----Original Message----- From: kk6ecm [mailto:kk6ecm@gmail.com] Sent: Sunday, May 22, 2016 10:37 AM To: 'app_rpt-users(a)ohnosec.org' Subject: RX Input Adjust Failed What could cause the Error: RX Input Adjust Failed? DONE tries=12, setting=1000, meas=58, sqnoise=13 ERROR: RX INPUT ADJUST FAILED. No RF input to the radio. I'm attempting to setup a substitute receiver for testing, but am experiencing difficulty setting it up, and not wanting to make a switch to simpleusb, thus making the minimum number of changes. The substitute receiver (Yaesu FT-1500M) is detecting CTCSS, with USB COR out, and I'm using the speaker output. (see below conf file) Any thoughts? Thanks, Bob kk6ecm 73 from usbradio_tune... hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=107.2 rxctcssfreqs=107.2 txctcssfreqs=107.2 ;rxctcssoverride=0 ;carrierfrom=dsp carrierfrom=usb ;dsp ctcssfrom=no ;usbinvert rxdemod=speaker ;flat txprelim=no txlimonly=no txtoctype=notone txmixa=composite txmixb=no invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0

3 8

RX Input Adjust Failed
by kk6ecm 22 May '16

22 May '16

What could cause the Error: RX Input Adjust Failed? DONE tries=12, setting=1000, meas=58, sqnoise=13 ERROR: RX INPUT ADJUST FAILED. No RF input to the radio. I'm attempting to setup a substitute receiver for testing, but am experiencing difficulty setting it up, and not wanting to make a switch to simpleusb, thus making the minimum number of changes. The substitute receiver (Yaesu FT-1500M) is detecting CTCSS, with USB COR out, and I'm using the speaker output. (see below conf file) Any thoughts? Thanks, Bob kk6ecm 73 from usbradio_tune... hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=107.2 rxctcssfreqs=107.2 txctcssfreqs=107.2 ;rxctcssoverride=0 ;carrierfrom=dsp carrierfrom=usb ;dsp ctcssfrom=no ;usbinvert rxdemod=speaker ;flat txprelim=no txlimonly=no txtoctype=notone txmixa=composite txmixb=no invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0

1 0

LOCALPLAY vs. PLAYBACK
by Steve Mahler 22 May '16

22 May '16

Is there some way that PLAYBACK can be configured to act differently? Here is the setup ... 1) I run an IAX session to my Node 2) I run an ECHOLINK session to the same Node 3) I monitor the repeater output 4) I run the command ... /usr/sbin/asterisk -rvx "rpt localplay $NODE $WX/talkit" ... it plays only on the repeater output, which is expected. 5) I run the command ... /usr/sbin/asterisk -rvx "rpt playback $NODE $WX/announce" ... it plays only on the repeater output, which I do not expect. I was under the impression that PLAYBACK when out on every connection to the node. What am I missing? I wanted this version to speak on all links. ...STeve - KF5VH

2 1

Re: [App_rpt-users] Voter RTCM sometimes offline-mode but not when there is a telnet connection
by info＠rainerbertsch.de 22 May '16

22 May '16

Am 22.05.2016 um 06:19 schrieb info(a)rainerbertsch.de: Hi Chuck, thanks for the answer of my request. Yes, RTCM and server are on the same LAN-segment. we use a switch (or better we tried several different switches) .because wie now think that there is a networkproblem. We also tried it with 10 MB/s full duplex on both sides . Is there any other possibility to use in the configuration of RTCM oder server ? I tried ping tests but did not se any thin special. Am 22.05.2016 um 00:19 schrieb Chuck Henderson <rpt2(a)chuck.midlandsnetworking.com <mailto:rpt2@chuck.midlandsnetworking.com>>: Is the RTCM and the server on the same Ethernet LAN at the same location? Are you using an Ethernet switch or a hub? If you are using a switch then why are you not running everything full duplex? On Sat, May 21, 2016 at 3:02 PM, info(a)rainerbertsch.de <mailto:info@rainerbertsch.de> <info(a)rainerbertsch.de <mailto:info@rainerbertsch.de>> wrote: Hi there, Since November, we are trying to build a voting system. We need some help please ! Hardware: Supermicro Intel Atom D525 (we also tried a RaspberryPi and an other computer) Software: Since yesterday DIAL from Alllstar-Homepage (Before we tried it with ACID) RTCM from Micro Node, Mark, we have 4 of them and tried all of them Garmin GPS 18x LVC, also wie tried 4 of them. Error: More or less often the RTCM switch in the offline mode. When there is traffic very often. But not if at the same time there is a telnet connection from any computer to the RTCM. We suspect a networking problem between our asterisk-server and RTCM Network-Card is set to 10 MB / s half-duplex like in the RTCM. From tcpdump from server to rtcm we got: ——— snip ---------- GPSTime (cli0_yy): 05/05/16 12:48:01.000000000 SysTime: 05/05/16 12:48:01.040000 DrainTime: 05/05/16 12:48:01.000 Got GPS (cli0_yy): Lat: 4857.60N, Lon: 00915.01E, Elev: 214.4 sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 GPSTime (cli2_bprx): 05/05/16 12:48:01.000000000 SysTime: 05/05/16 12:48:01.300000 DrainTime: 05/05/16 12:48:01.240 Got GPS (cli2_bprx): Lat: 4853.16N, Lon: 00912.65E, Elev: 317.2 sending KEEPALIVE (GPS) packet to client cli0_yy digest 79d9c77d GPSTime (cli0_yy): 05/05/16 12:48:02.000000000 SysTime: 05/05/16 12:48:02.040000 DrainTime: 05/05/16 12:48:02.000 Got GPS (cli0_yy): Lat: 4857.60N, Lon: 00915.01E, Elev: 214.4 sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 [May 512:48:03]NOTICE[6559]:chan_voter.c:3632voter_reader:Voter lost master timing source!! sending packet challenge 200371797 digest 7749985d password BLAH sending packet challenge 200371797 digest 7749985d password BLAH sending packet challenge 200371797 digest bbb4c643 password BLAH GPSTime (cli2_bprx): 05/05/16 12:48:18.000000000 SysTime: 05/05/16 12:48:18.320000 DrainTime: 01/01/70 01:00:00.340 Got GPS (cli2_bprx): Lat: 4853.16N, Lon: 00912.65E, Elev: 317.2 -- Voter client cli0_yy disconnect (timeout) sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 ——— snip ---------- Konfiguration of the Ethernet-Card # ethtool eth0 Settings for eth0: Supported ports: [TP] Supported link modes: 10baseT / Half 10baseT / Full 100baseT / Half 100baseT / Full 1000baseT / Full Supported break frame use: No Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised break frame use: No Advertised auto-negotiation: No Speed: 10Mb / s Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv sample link Does anyone have an idea what it may be ? Why there is no problem with telnet at the same time and how can we run the system without this workaround -- Rainer Bertsch DF3SY _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

. usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee
by KM4NRJ FLORIDA 22 May '16

22 May '16

If you are using Xipar then under the CLI use: radio probe on It will scan all currently connected Fobs and indicate bus and device number. radio probe off will stop the scan. Edit the urd.conf file to set device parameters accordingly. Restart Asterisk On May 21, 2016 17:08, <app_rpt-users-request(a)ohnosec.org> wrote: Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee) 2. Voter RTCM sometimes offline-mode but not when there is a telnet connection (info(a)rainerbertsch.de) 3. Re: usbradio_tune_xxxxx.conf where .conf = .confusion (kk6ecm) 4. Re: usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee) ---------------------------------------------------------------------- Message: 1 Date: Sat, 21 May 2016 14:04:56 -0500 From: Steve Agee <n5zua(a)earthlink.net> To: app_rpt-users(a)ohnosec.org Subject: [App_rpt-users] usbradio_tune_xxxxx.conf where .conf = .confusion Message-ID: <c5dc4bf0-2c2c-3566-f32e-31a311653463(a)earthlink.net> Content-Type: text/plain; charset="windows-1252"; Format="flowed" Hello list: I've searched <http://www.xelatec.com/xipar/node/180> and I fully understand the description/explanations given. What I don't understand, with specific attention to the lines: |; name=usb ; ; devnum=1 ; devstr=4-2 ; is how to manually uncomment, and manipulate them. In this particular instance, I'm trying to get a DIAL box running with one original URI (early version) using the USBRADIO channel driver, and one URIX (newer version) using the SIMPLEUSB channel driver. I've followed the step-by-step (or was that Crossbar 5 Duude?) instructions for starting off with a single node, then adding the second node. That simply doesn't work. The second URIx green L.E.D. stays solid throughout the process. Are these lines provided for informational purposes only, or can they be edited to force the second device to be recognized and assigned? N5ZUA |

3 8

As in the words.....
by KM4NRJ FLORIDA 22 May '16

22 May '16

Probably dated but in the words of the General on the original movie Wargames.... "I would pxxs on a spark plug if I thought it would help. " " computers only do what they are instructed to do. We just need to figure out what it was we said. " On May 21, 2016 18:59, <app_rpt-users-request(a)ohnosec.org> wrote: Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (David McGough) 2. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (Steve Agee) 3. Re: Voter RTCM sometimes offline-mode but not when there is a telnet connection (Chuck Henderson) 4. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (David McGough) 5. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (Steve Agee) ---------------------------------------------------------------------- Message: 1 Date: Sat, 21 May 2016 18:13:00 -0400 (EDT) From: David McGough <kb4fxc(a)inttek.net> To: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee Message-ID: <Pine.LNX.4.44.1605211807150.17143-100000(a)goliath.inttek.net> Content-Type: TEXT/PLAIN; charset=US-ASCII For any of the AllStar releases: Launch Asterisk from the command prompt. asterisk> radio active usb asterisk> radio tune save If two URI's are attached, perform: asterisk> radio active usb1 asterisk> radio tune save If three URI's are attached, perform: asterisk> radio active usb2 asterisk> radio tune save ...Then, the usbradio_tune_xxx.conf file(s) will be pre-configured with what the AllStar software interprets the various devstr parameters to be. asterisk> exit On Sat, 21 May 2016, Steve Agee wrote: > Thanks, but as previously mentioned, this is DIAL and so your CLI > commands from XIPAR do not exist. > > N5ZUA > ------------------------------ Message: 2 Date: Sat, 21 May 2016 17:15:13 -0500 From: Steve Agee <n5zua(a)earthlink.net> To: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee Message-ID: <806c3361-90f7-64cb-9533-173f12638871(a)earthlink.net> Content-Type: text/plain; charset="windows-1252"; Format="flowed" Yes, and this works if everything is USBRADIO. But remember, one is USBRADIO and one is SIMPLEUSB. Ah, now the fun begins. N5ZUA On 5/21/2016 5:13 PM, David McGough wrote: > For any of the AllStar releases: > > Launch Asterisk from the command prompt. > > asterisk> radio active usb > asterisk> radio tune save > > If two URI's are attached, perform: > > asterisk> radio active usb1 > asterisk> radio tune save > > If three URI's are attached, perform: > > asterisk> radio active usb2 > asterisk> radio tune save > > ...Then, the usbradio_tune_xxx.conf file(s) will be pre-configured with > what the AllStar software interprets the various devstr parameters to be. > > asterisk> exit > > > > > On Sat, 21 May 2016, Steve Agee wrote: > >> Thanks, but as previously mentioned, this is DIAL and so your CLI >> commands from XIPAR do not exist. >> >> N5ZUA >> > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >

1 0

Voter RTCM sometimes offline-mode but not when there is a telnet connection
by info＠rainerbertsch.de 21 May '16

21 May '16

Hi there, Since November, we are trying to build a voting system. We need some help please ! Hardware: Supermicro Intel Atom D525 (we also tried a RaspberryPi and an other computer) Software: Since yesterday DIAL from Alllstar-Homepage (Before we tried it with ACID) RTCM from Micro Node, Mark, we have 4 of them and tried all of them Garmin GPS 18x LVC, also wie tried 4 of them. Error: More or less often the RTCM switch in the offline mode. When there is traffic very often. But not if at the same time there is a telnet connection from any computer to the RTCM. We suspect a networking problem between our asterisk-server and RTCM Network-Card is set to 10 MB / s half-duplex like in the RTCM. From tcpdump from server to rtcm we got: ——— snip ---------- GPSTime (cli0_yy): 05/05/16 12:48:01.000000000 SysTime: 05/05/16 12:48:01.040000 DrainTime: 05/05/16 12:48:01.000 Got GPS (cli0_yy): Lat: 4857.60N, Lon: 00915.01E, Elev: 214.4 sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 GPSTime (cli2_bprx): 05/05/16 12:48:01.000000000 SysTime: 05/05/16 12:48:01.300000 DrainTime: 05/05/16 12:48:01.240 Got GPS (cli2_bprx): Lat: 4853.16N, Lon: 00912.65E, Elev: 317.2 sending KEEPALIVE (GPS) packet to client cli0_yy digest 79d9c77d GPSTime (cli0_yy): 05/05/16 12:48:02.000000000 SysTime: 05/05/16 12:48:02.040000 DrainTime: 05/05/16 12:48:02.000 Got GPS (cli0_yy): Lat: 4857.60N, Lon: 00915.01E, Elev: 214.4 sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 [May 512:48:03]NOTICE[6559]:chan_voter.c:3632voter_reader:Voter lost master timing source!! sending packet challenge 200371797 digest 7749985d password BLAH sending packet challenge 200371797 digest 7749985d password BLAH sending packet challenge 200371797 digest bbb4c643 password BLAH GPSTime (cli2_bprx): 05/05/16 12:48:18.000000000 SysTime: 05/05/16 12:48:18.320000 DrainTime: 01/01/70 01:00:00.340 Got GPS (cli2_bprx): Lat: 4853.16N, Lon: 00912.65E, Elev: 317.2 -- Voter client cli0_yy disconnect (timeout) sending KEEPALIVE (GPS) packet to client cli2_bprx digest bbb4c643 ——— snip ---------- Konfiguration of the Ethernet-Card # ethtool eth0 Settings for eth0: Supported ports: [TP] Supported link modes: 10baseT / Half 10baseT / Full 100baseT / Half 100baseT / Full 1000baseT / Full Supported break frame use: No Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised break frame use: No Advertised auto-negotiation: No Speed: 10Mb / s Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv sample link Does anyone have an idea what it may be ? Why there is no problem with telnet at the same time and how can we run the system without this workaround -- Rainer Bertsch DF3SY

2 1

1. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion
by KM4NRJ FLORIDA 21 May '16

21 May '16

Sorry for the mistake. For some reason the previous Xelatec links caused me to think of that. But it is an address issue. I just got finished with a Xipar node that did the same behavior. Ran fine, Green light lit but no heartbeat. Despite hot swapping the fobs which resulted in the OS seeing it, I finally realized the tune file forced the selection. Good luck as I don't run DIAL 73s On May 21, 2016 5:38 PM, <app_rpt-users-request(a)ohnosec.org> wrote: Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (Steve Agee) ---------------------------------------------------------------------- Message: 1 Date: Sat, 21 May 2016 16:38:16 -0500 From: Steve Agee <n5zua(a)earthlink.net> To: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee Message-ID: <ba084f3d-f4d2-017b-04e4-11c5cace0f7d(a)earthlink.net> Content-Type: text/plain; charset="windows-1252"; Format="flowed" Thanks, but as previously mentioned, this is DIAL and so your CLI commands from XIPAR do not exist. N5ZUA On 5/21/2016 4:36 PM, KM4NRJ FLORIDA wrote: > > Excuse my mistake. > > Edit the urd_tune_usb.conf not urd.conf > > On May 21, 2016 17:08, <app_rpt-users-request(a)ohnosec.org > <mailto:app_rpt-users-request@ohnosec.org>> wrote: > > If you are using Xipar then under the CLI use: > > radio probe on > > It will scan all currently connected Fobs and indicate bus and > device number. > > radio probe off > > will stop the scan. > > Edit the urd.conf file to set device parameters accordingly. > > Restart Asterisk > > On May 21, 2016 17:08, <app_rpt-users-request(a)ohnosec.org > <mailto:app_rpt-users-request@ohnosec.org>> wrote: > > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org <mailto:app_rpt-users@ohnosec.org> > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > <mailto:app_rpt-users-request@ohnosec.org> > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > <mailto:app_rpt-users-owner@ohnosec.org> > > When replying, please edit your Subject line so it is more > specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. usbradio_tune_xxxxx.conf where .conf = .confusion (Steve > Agee) > 2. Voter RTCM sometimes offline-mode but not when there is a > telnet connection (info(a)rainerbertsch.de > <mailto:info@rainerbertsch.de>) > 3. Re: usbradio_tune_xxxxx.conf where .conf = .confusion > (kk6ecm) > 4. Re: usbradio_tune_xxxxx.conf where .conf = .confusion > (Steve Agee) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sat, 21 May 2016 14:04:56 -0500 > From: Steve Agee <n5zua(a)earthlink.net > <mailto:n5zua@earthlink.net>> > To: app_rpt-users(a)ohnosec.org <mailto:app_rpt-users@ohnosec.org> > Subject: [App_rpt-users] usbradio_tune_xxxxx.conf where .conf = > .confusion > Message-ID: > <c5dc4bf0-2c2c-3566-f32e-31a311653463(a)earthlink.net > <mailto:c5dc4bf0-2c2c-3566-f32e-31a311653463@earthlink.net>> > Content-Type: text/plain; charset="windows-1252"; Format="flowed" > > Hello list: > > I've searched > > <http://www.xelatec.com/xipar/node/180> > > and I fully understand the description/explanations given. > What I don't > understand, with specific attention to the lines: > > |; name=usb ; > ; devnum=1 ; > devstr=4-2 ; > > is how to manually uncomment, and manipulate them. In this > particular > instance, I'm trying to get a DIAL box running with one > original URI > (early version) using the USBRADIO channel driver, and one > URIX (newer > version) using the SIMPLEUSB channel driver. I've followed the > step-by-step (or was that Crossbar 5 Duude?) instructions for > starting > off with a single node, then adding the second node. That > simply doesn't > work. The second URIx green L.E.D. stays solid throughout the > process. > Are these lines provided for informational purposes only, or > can they be > edited to force the second device to be recognized and assigned? > > N5ZUA > > | >

1 0

Xipper ?
by R Gross 21 May '16

21 May '16

Is there a xipper install for raspberry PI available ? Ryan n3ssl

1 0

What does "fever=1" tell me in usbradio_tune_xxxxx.conf after setting up the receiver?
by kk6ecm 21 May '16

21 May '16

What does "fever=1" tell me in usbradio_tune_xxxxx.conf after setting up the receiver? Thanks, Bob kk6ecm 73

3 6