- App_rpt-users - lists.keekles.org

simplex vs duplex for a home node
by Elden Fenison 18 Jan '15

18 Jan '15

Please excuse my ignorance on this. But one of the advantages of Allstar over say IRLP is the ability to operate full-duplex. My understanding on this is limited. But apparently full-duplex is not possible without setting up a repeater. Since many folks seem to setup nodes in their residences... is it common for them to have repeater setups that allow them full-duplex operation at home? Is there a relatively cheap/easy way to do this? Any tips are very appreciated. :)

7 11

Re: [App_rpt-users] Get the same USB port assigned to a node at startup each time?
by Bryan Fields 17 Jan '15

17 Jan '15

On 1/17/15, 10:51 PM, Cole Cunningham wrote: > I haven’t gotten to the point of setting up the FOBs so haven’t done the tune > yet. I just looked and see the radio tune rxnoise, etc commands and will need > to get a radio interfaced to set them. Cole, If these are all local nodes, you might want to consider the quad pci radio card. It's more reliable (IMHO) than the typical usb interface when used in production. -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Re: [App_rpt-users] Allstarlink (app_rpt) with low power PC's?
by mike＠midnighteng.com 16 Jan '15

16 Jan '15

Well, Doug - WA3DSP put the time into a well documented version for the BeagleBoneBlack BBB It can be found at http://hamvoip.org/BBB/BBB_Allstar_v1.2.1.zip http://crompton.com/hamradio/BeagleBoneBlackAllstar/ Many of these are in use now. ...mike/kb8jnm > -------- Original Message -------- > Subject: [App_rpt-users] Allstarlink (app_rpt) with low power PC's? > From: Thomas Delmonego <delmonego(a)hotmail.de> > Date: Wed, January 14, 2015 8:45 am > To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > > > Hi all, > > have anyone realised an efficient Allstarlink-System with CTCSS and COR elaborated by DSP (using configuration in "usbradio.conf") using low power computers such Odroid, Banana Pi, Cubieboard, Wandboard or similars? > > If reply is yes (yahoo!), is there available an ISO file for used memory (compact flash, micro SD etc.) ? > > 73! Thomas, IW3AMQ<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

8 7

Weird behavior
by Mike M 14 Jan '15

14 Jan '15

I have two nodes set up. One of them is a DMK URI the other is a CM119 dongle. Both are in full duplex mode 3. I have an HT connected to the DMK with a COR signal going in (internally tied to the squelch light). PTT is not connected to the HT. I link both nodes and have a speaker on the CM119. The behavior I expect is when the COR goes high, both nodes should PTT, and both nodes should pass audio from the HT. It seems that when audio is active, the green light flashes fast, so I will say I expect that as well. But what I get is this: When a signal comes into the HT, both dongles PTT are activated reliably (I added a red LED to the CM119), but randomly, one or both dongles will not pass audio (which also seems to be tied to the green light flashing fast.) So randomly one, the other, both, or none of the dongles will start flashing the green LED fast when the COR goes high (PTT always activates). If the CM119 green light flashes fast, I hear audio out of the speaker regardless if the DMK is flashing fast (not monitoring audio on that node) When I do head audio, mid transmission, the audio will just stop and the green lights will go back to the slow flash, but the PTT will remain high. Watching the console, nothing comes up when the audio stops. But when the COR is dropped, the PTT is also dropped on both dongles and I see -- Hungup 'Zap/pseudo-[some number]'. Load average is low, ~0.2 when this happens. I previously had this all working with 6 nodes pretty well but now I can't even get 2 working reliably. This is with simpleUSB. Any dieas? I just recompiled with the radio_relax flag unset as in Dougs simpleusb howto because I was getting random DTMF triggers which I thought might be causing it, but I'm not getting those anymore and it's still a problem. I am seeing these messages randomly, but they do not appear to be tied to any external actions. WARNING[27142]: app_rpt.c:9526 rpt_tele_thread: telem_lookup:ctx failed on Zap/pseudo-393439155 On a side note, is there a way to keep allstar from trying to register private nodes? I keep getting the Registration Refused messages pop up in the console. Thanks Regards, Mike Montalvo, KF7MBK

2 2

Need help DD command
by Robert Newberry 14 Jan '15

14 Jan '15

I recently set-up a BBB. When getting the image from www.hamvoip.net I tried use my new installation of Ubuntu 14.04, mostly because I am trying to learn Linux by just using it. I didn’t have any luck and just to keep the project moving I resorted back to windows to complete the image copy. I would like to learn how to copy a .img file to a micro sd card using DD. I would also like to know how to do the reverse of taking a micro sd card and making a .img file for backup. Is there anyone on the list willing to help me with this? Thank you Bob/N1XBM

2 1

Quad Radio PCI card Voltage?
by Bryan Fields 14 Jan '15

14 Jan '15

Quick question, is this card a universal 3.3/5v card or 3.3 or 5v? It looks like it's universal, but I want to be sure. I'm traveling so I can't pull out my spare and look. 73's -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Allstarlink (app_rpt) with low power PC's?
by Thomas Delmonego 14 Jan '15

14 Jan '15

Hi all, have anyone realised an efficient Allstarlink-System with CTCSS and COR elaborated by DSP (using configuration in "usbradio.conf") using low power computers such Odroid, Banana Pi, Cubieboard, Wandboard or similars? If reply is yes (yahoo!), is there available an ISO file for used memory (compact flash, micro SD etc.) ? 73! Thomas, IW3AMQ

1 0

Re: [App_rpt-users] help with installing CentOS
by mike＠midnighteng.com 12 Jan '15

12 Jan '15

Here I am guessing a little based on what you have said. .......... The file you are downloading is a ISO it is a standard image for a CD (in our case) You need to just download/save the file on your computer. Then when download is complete, Open you favorite CD burning software and CREATE A CD FROM A ISO IMAGE. Pointing to the iso image you just downloaded. Now what exactly it says in your software is unknown to me. But that is the basics of it. Once you have your burned CD, set your computer up to boot from CD ROM, (probably does allready) Put freshly burned CD in and start machine.Follow on screen instruction. Hopefully that is what you were looking for. ...mike/kb8jnm > -------- Original Message -------- > Subject: [App_rpt-users] help with installing CentOS > From: frank roff <kh6bfd(a)yahoo.com> > Date: Mon, January 12, 2015 8:19 pm > To: app_rpt-users(a)ohnosec.org > > > Hi All, > I am trying to install the OS to build my server for Allstar. I clicked the link and downloaded the file as it says to. > But, all I get is a Sonic recorder with a file. The file when I click on it just opens up another recording file. I also tried to reboot > with the cd in and the bios is set to boot from cd. But, still nothing happens. Any ideas what I am doing wrong??? > > Frank > KH6BFD > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

help with installing CentOS
by frank roff 12 Jan '15

12 Jan '15

Hi All, I am trying to install the OS to build my server for Allstar. I clicked the link and downloaded the file as it says to. But, all I get is a Sonic recorder with a file. The file when I click on it just opens up another recording file. I also tried to reboot with the cd in and the bios is set to boot from cd. But, still nothing happens. Any ideas what I am doing wrong??? Frank KH6BFD

1 0

Re: [App_rpt-users] Node Status not showing...
by Jah Rastafari 12 Jan '15

12 Jan '15

Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air... Bob/KK6RQ On Sun, Jan 11, 2015 at 8:28 PM, <mike(a)midnighteng.com> wrote: > > > You could be having some problems with internet host (especially if it > is comcast). > Probably temporary, don't go changing your settings over it just yet. > Give it a few days and reboots (computer and router) to see how it pans > out. > > > ...mike/kb8jnm > > > -------- Original Message -------- > > Subject: Re: [App_rpt-users] Node Status not showing... > > From: Jah Rastafari <nuhtrue(a)gmail.com> > > Date: Sun, January 11, 2015 9:20 pm > > To: mike(a)midnighteng.com, "app_rpt-users(a)ohnosec.org" > > <app_rpt-users(a)ohnosec.org> > > > > > > I went back right after reading your reply (several hours after my > original > > post) and it in fact came up the way it should. But then 5 minutes > > later it went back to saying I wasn't connected. I'm not sure what it > means > > but I can say I've never seen it behave like this before. > > > > On Sun, Jan 11, 2015 at 4:56 PM, <mike(a)midnighteng.com> wrote: > > > > > > > > > > > > > > Not sure but.... > > > > > > I think you are only suffering from a delay of the update to the list. > > > > > > Try waiting for a short while (up to 30min) and look again. > > > Others have said it takes that long sometimes but I have only witnessed > > > about 5-6min. > > > > > > Guess it depends on how busy the server is. > > > > > > > > > ...mike/kb8jnm > > > > > > > -------- Original Message -------- > > > > Subject: [App_rpt-users] Node Status not showing... > > > > From: Jah Rastafari <nuhtrue(a)gmail.com> > > > > Date: Sun, January 11, 2015 5:29 pm > > > > To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > > > > > > > > > > > > Forgive me if this has already been discussed and I missed it, but I > just > > > > noticed recently that although I was connected to a number of other > > > > nodes/repeaters, the 'Node Status' selection on the Allstar site > says I'm > > > > not connected to anything. My node(s) show up properly in the > available > > > > node list and everything else is as it should be. The Web Transceiver > > > works > > > > properly also and I haven't changed anything recently. Am I missing > > > > something? > > > > > > > > Bob/ KK6RQ<hr>_______________________________________________ > > > > App_rpt-users mailing list > > > > App_rpt-users(a)ohnosec.org > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > > > To unsubscribe from this list please visit > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > down > > > to the bottom of the page. Enter your email address and press the > > > "Unsubscribe or edit options button" > > > > You do not need a password to unsubscribe, you can do it via email > > > confirmation. If you have trouble unsubscribing, please send a message > to > > > the list detailing the problem. > > > >

4 5