- App_rpt-users - lists.keekles.org

Possible bug?
by Ken Page 16 Oct '10

16 Oct '10

Have had a weird thing lately where the DMK interface locks up and the green light stops flashing. Restarting Asterisk doesn't help. After a restart I get this. [Oct 16 23:04:54] WARNING[8789]: chan_usbradio.c:1828 setformat: Unable to set format to 16-bit signed [Oct 16 23:04:54] WARNING[8789]: chan_usbradio.c:1449 hidthread: Loaded parameters from usbradio_tune_usb.conf for device usb . [Oct 16 23:04:54] WARNING[8789]: chan_usbradio.c:1828 setformat: Unable to set format to 16-bit signed A complete reboot of the system get's it up again. The user was accessing echolink node GB3KD-R both times when it failed. Regards, Ken - vk4akp Mt Crosby Repeater - vk4akp All_Star# 2134, Echolink# 7878. Ipswich Metro Radio Group .-.-.

2 1

Re: [App_rpt-users] Finally, GPIO signals on a USB device!!!
by Jim Duuuude 14 Oct '10

14 Oct '10

I have added the ability to "pulse" (that is, invert its current state for a period of time) a GPIO output for a specifed amount of time. See additional docs at: http://app-rpt.qrvc.com/nodes/177 JIM

1 1

FS: Quad PCI, Hamtronics 2M
by Eric Tichansky 14 Oct '10

14 Oct '10

I have a Quad PCI board for sale, purchased around Jan 2009. Local repeater project moving in other directions. Fully working and lightly used. Asking $450 OBO. Also have a Hamtronics 2M repeater purchased around the same time. Includes REP-200 chassis, RX module, TX module, and 2M 20W PA. TX/RX modules are DIP switch frequency controlled. TX module PA transistor was replaced during winter of 2009 due to locked TX. Working normally last time it was powered up and tested. All other modules (including 20W PA module) were unaffected. Asking $550 + shipping OBO (price reflects only value of chassis, RX, and PA since the TX module *was* damaged, though repaired). Contact off-list no3m at no3m.net 73 - Eric NO3M

1 0

Re: [App_rpt-users] Login incorrect
by Corey Dean N3FE 13 Oct '10

13 Oct '10

As I stated in the past, your login is root and your password is whatever you made it during the install process. This seperate from the portal login. Corey Sent from my Droid! ----- Reply message ----- From: "Darril Holland" <holldrl(a)gt.rr.com> Date: Mon, Oct 11, 2010 1:46 pm Subject: [App_rpt-users] Login incorrect To: "app_rpt-users(a)qrvc.com" <app_rpt-users(a)qrvc.com> After server boots up, I get groves1 login(my server). Type in callsign and password, I get Login incorrect. What could cause this?What should I get when this problem is solved? Darril -- This message was scanned and is believed to be clean. Click here to report this message as spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=349F72FC71.AE18E>

2 1

ACID Install with USB Thumb Drive vs CD-ROM
by Keith Dobbins 13 Oct '10

13 Oct '10

Just wondering if it was possible to do a acid install without a CD-ROM Drive? I tried uunetbootin but it gives me that it can't find the kickstart file. I figure it's the difference in file systems for the install. I haven't played around with linux for a while but could eventually get it to work the more I played with it bu just didn't want to reinvent the wheel. I have tons of usb thumb drives but limited access to a usb cd-rom (have to borrow from a friend). Thanks! Keith Dobbins A.S. Flight Paramedic 3402 Linden Street Parkersburg, WV 26104-1608 Amateur Radio Call Sign: KC8RFW

1 0

Re: [App_rpt-users] Squelch trigger
by Bogdan Diaconescu 13 Oct '10

13 Oct '10

Thanks Matt, I noticed the option in sourcecode. Regards, Bogdan > The feature you need is already built in to the system. > > Look for "Rxondelay" in USBradio.conf > > This will allow you to set the time during which the Rx COS is ignored, > after the PTT is dropped. > > I have used this in the past to stop two linked repeaters ping ponging. > > Regards, > > Matt > > On 12 October 2010 17:42, Bogdan Diaconescu <yo3iiu(a)yo3iiu.ro> wrote: > >> Hello, >> >> I'm using app_rpt to build a repeater system using COR and PTT >> signaling. >> The issue I'm having is that after each PTT off I got a COR enable from >> rig for a constant amount of time of 30ms which triggers another PTT on >> and so on. Therefore I'm looking for a solution to overcome this >> problem. >> >> Specifically, what I need is an option that will trigger COR to app_rpt >> only when COR was active for an user specified period of time (say 50ms >> in >> my case). >> >> Thanks and regards, >> Bogdan - YO3IIU >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)qrvc.com >> http://qrvc.com/mailman/listinfo/app_rpt-users >> >

3 2

Re: [App_rpt-users] cheap USB fobs
by Yokshs 13 Oct '10

13 Oct '10

Hello Pete, Tried replying directly, but the email bounced... The DealExtreme item was SKU# 21812 https://www.dealextreme.com/details.dx/sku.21812 I received 3 "blobs" and one CM119 that seems to be defective. FWIW, it seems like they might be willing to refund my purchase price if I return the items. I'll believe it when my Paypal account grows by $28. hi hi 73. Kyle K0KN ----- Original Message ----- From: "Peter Elke" To: <yokshs Sent: Monday, October 11, 2010 1:56 PM Subject: FW: [App_rpt-users] cheap USB fobs Hi Kyle, Which one did you buy on dealextreme? There seems to be lots of USB audio fobs on there... 73's Pete (WI6H)

4 3

Allstar-APRS/GPS Newbie needs help
by Darril Holland 12 Oct '10

12 Oct '10

If anyone out there has the APRS/GPS enabled on their sever, and has time to help me get mine going.I need info and have questions.Thanks,Darril/WD5GJP

1 0

Squelch trigger
by Bogdan Diaconescu 12 Oct '10

12 Oct '10

Hello, I'm using app_rpt to build a repeater system using COR and PTT signaling. The issue I'm having is that after each PTT off I got a COR enable from rig for a constant amount of time of 30ms which triggers another PTT on and so on. Therefore I'm looking for a solution to overcome this problem. Specifically, what I need is an option that will trigger COR to app_rpt only when COR was active for an user specified period of time (say 50ms in my case). Thanks and regards, Bogdan - YO3IIU

1 0

Re: [App_rpt-users] Finally, GPIO signals on a USB device!!!
by Doug Hutchison 12 Oct '10

12 Oct '10

Hello Jim, Can you please post the necessary steps to obtain and install said file in simple terms please. Thank you, D On 10/10/2010 19:30:49, Jim Duuuude (telesistant(a)hotmail.com) wrote: > I discovered (not with any help from the lack of documentation from C-media) that the 'HOOK' signal is > actually available to be read (but not written). Therefore, the "GPIO2" signal can at least now be used > as an input. > > The code revision (chan_usbradio.c) to support this should be available via SVN at abut 12:15 PDT today (when the public > SVN server updates). > > Well, it's better then nothing...... > > JIM WB6NIL

3 4