October 2013 - App_rpt-users - lists.keekles.org

Morse command
by Scott Weis 05 Oct '13

05 Oct '13

I would like to send a Morse code sequence on command, is there any way to do this currently? Thanks & 73, Scott

1 0

Icom F510 / F610
by keith 05 Oct '13

05 Oct '13

Good afternoon from the UK, Has anyone installed an Icom F510 or F610 as a node radio? I managed to locate a 9 pin APC-617 aux connection and the following detail from Icom. Any help would be great Port definition as detailed. I have built the CM108 USB key fob and at present use a Motorola GM 380 PMR this works great but its nice to have a spare radio. Kind Regards Keith Handscombe G7DNT

2 1

streaming restart
by Ken 05 Oct '13

05 Oct '13

How can I restart "ezstream" (app_rpt outstream command) without rebooting my system? It seems like my internet provider has taken to disconnecting my internet access for 1 minute each morning. That results in a source disconnect at my streaming host server (which is probably what they intend!). Restarting the host server does not reestablish the connection. Seems I have to restart it at my end. Thanks Ken

1 0

long tail
by Ken 04 Oct '13

04 Oct '13

You get a long tail when you are using CTCSS and COR and the COR is continuously on (indicating carrier present). Asterisk operates only on the tone squelch, in that case. Something is wrong with your COS (COR) signal or related configuration. 73 Ken

2 1

Re: [App_rpt-users] ACID Centos6
by Johnny Keeker 04 Oct '13

04 Oct '13

'ACID Centos6 on a 1.8G, 4G ram, 120G ssd, 64 bit computer test results.' hile injecting a 1khz tone at 3khz into node #1 receiver, the waveform on node #2 transmitter has a ripple. Configured as a simplex node with a URI, connected to a second node, receivable with a service monitor, w Reverse this test and the waveform on node #1 transmitter is clean. Using the exact hardware, conducting the same test with ACID centos5, and Xipar centos6, the waveform is remains clean. I am not experienced at this, but I took a long shot and recompiled the software with different channel drivers. The results were the same. I haven't seen much chatter about ACID Centos6, so I thought commenting on the findings may spark some interest. Comments or Criticisms accepted gracefullyJK

2 2

Permalink
by Mark Johnston 04 Oct '13

04 Oct '13

Does anyone know what is up with the permalink command I have it setup as this: 76=ilink,12 ; Permanently connect specified link -- monitor only 77=ilink,13 ; Permanently connect specified link -- transceive When I do *7628344 from my private node 1001 it connects but will not stay when I disconnect all aka *71... also when I do a status on 28344 it says transceive... not the monitor only. Is there a diff iLink i should use to disconnect all 'non-permalink' links? 71=ilink,6 Thanks... Mark KC7DMF

2 3

Anyone happy with Beagleboard/URI combo?
by Paul Schlacter 03 Oct '13

03 Oct '13

Hello Group, While I see several threads discussing the possible combination of the Beagleboard/URI combo, I have yet to see anyone mention that the combination works, and that they are happy with it. I would like to add a simple node to one of the free ports on my controller, and I want to keep power consumption at a minimum. I want to avoid using the LOX because I have been assured that the URI has better audio. Is anyone using this combination? Are you happy with it? If there is indeed a thread where people mention that this combination works, I apologize in advance for not being able to find it. Thanks! -Paul

2 1

echolink proxy
by Greg 02 Oct '13

02 Oct '13

Hello. Is there a way to utilize echolink proxy using allstar (acid)? I couldn't find anything obvious in echolink.conf. I move around a lot and don't always have time to get ports forwarded. I maintain a proxy for this reason.. Thanks Greg

3 2

VMWare Player Virtual Machine Putty or Win SCP
by Jim W7RY 02 Oct '13

02 Oct '13

Has anyone successfully used putty to log onto a VMWare Player virtual machine? What IP did you use? How about Win SCP? Thanks 73 Jim W7RY

1 1

Beagle Board stops working after configuring Echolink
by Drew Scelba 01 Oct '13

01 Oct '13

I am using a beagle/LOX combo and when I try turning on echolink it IAX protocol will no longer register my node. An I am not able to connect to any allstar nodes but I can connect to echo link. Has anyone experienced this problem or have any suggestion on how to fix the problem. Thank, Drew N2RFA

1 0