October 2013 - App_rpt-users - lists.keekles.org

How to configure non DSP on a URI
by Lu Vencl 15 Oct '13

15 Oct '13

I am trying to help someone attach a node to a CAT controller and this is the first time EVER that I am not using DSP. Seems like we are having issues with COR and also RX audio. Since I have never used these inputs, we need some help. Here is a sample entry in the URD file and was hoping that someone might be able to supply a few tips. I am not using CTCSS so I said "no" and am using a logic high when no RX signal present, the CAT controller drags down to 0 volts upon signal detection on the repeater receiver. I am not getting any action when this happens though. I even tried to use "USBINVERT" but that had no effect. I see about 3 volts when idle. Any thoughts? Note I even tried to use VOX and that did not work for some reason. hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=1 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi carrierfrom=usb ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxboost=0 ; rx input boost of 20dB rxdemod=speaker ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit Thanks! Lu Vencl, KA4EPS

2 1

RTCM bandwidth/ data throughput requirements?
by Paul Schlacter 15 Oct '13

15 Oct '13

Good Morning,Group! I am curious as to the bandwidth/data throughput requirements of the Allstar RTCM. I wish to use a dedicated microwave link that will permit up to 20Mbps. Would that work for the RTCM? Thank you! -Paul

3 2

Shortcuts in DTMF
by keith 15 Oct '13

15 Oct '13

Evening all, I have on my All-Star node some DTMF short-cuts and would like to add more. I have at the moment used the list below but would like to add 30 short-cuts in total as the older hams have a problem sending more than 2-3 characters so when asked to connect to an Echo link node 1234 its very difficult for the older hams to key *33001234. We have tried several times and with 1 attempt that work from almost 35 goes at this the poor old boy quote " It's a bit too much for me as I am 88 I struggle to see the buttons let alone press in any order" So if this is difficult I am happy to keep the list below and change it daily to suite the older hams having then a daily list of favourites in a weekly format so all 30 short-cuts can be achieved over a 4 week period. If it's not to difficult then I will have a go Many thanks whoever lends a hand Kind Regards Keith Handscombe G7DNT

3 2

Sort of OFF TOPIC but sort of ON topic
by Bradley Haney 15 Oct '13

15 Oct '13

What flavor's for Asterisk has App_rpt that i can still use for my repeater with w DMK URI? I didn't know if elastix, etc would work . I tried Xipar but every time i get it going and make a change that is wong like adding a sip provider it just bomb's to the point its easier to re install the software. I am currently using ACID but would like to something with a graphical interface for the telephone stuff to add IVR's etc.. any thoughts? Thanks Bradley

1 0

Interfacing with a Vertex repeater.
by Bradley Haney 13 Oct '13

13 Oct '13

Would it hurt the repeater to set up the computer box with a duplex=3 but still let the repeater do the repeating also. That way if the computer dies the repeater keeps working? didn't know if it would hurt the repeater since the URI would be trying to inject audio the same time the repeater was doing it also.. Bradley

2 5

OT: on an entirely different topic...
by Bryan D. Boyle 13 Oct '13

13 Oct '13

anyone have any guidance on where/how to find the interface sigs on a uhf mid power batwing spectra and rss stuff to get to work as a simplex node in asterisk. just brought up my 900 msf5k on the system, but off the net for now (waiting for a clinb to put up the ubiquity 5.8 link back to the house)...thought of standing up a quick rf link for now. back to our regularly scheduled program...:) -- Bryan Sent from my iPhone 5...small keyboard, big fingers...please forgive misspellings...

1 0

ARRL WAS Re: App_rpt-users Digest, Vol 56, Issue 28
by Lloyd Colston 12 Oct '13

12 Oct '13

On Fri, Oct 11, 2013 at 1:54 PM, <app_rpt-users-request(a)ohnosec.org> wrote: > yeah, it still has some mindshare (especially amongst the dinosaurs in the > ARRL, who refuse to acknowledge that allstar exists...and despite the > population of a* approaching that of the older stuff, have refused to list > our nodes as such in the repeater directory...), but progress waits for no > man. > As one of the dinosaurs at the ARRL and a Quarter Century Wireless Association member to boot, please allow that: 1. The ARRL is only one repeater directory publisher. As mentioned earlier, http://www.repeaterbook.com/ where I am a moderator and http://www.artscipub.com/repeaters/ are just two. I don't see many nodes listed on the latter two, though coordinated REPEATERS are. After all, it is a REPEATER directory. I have our simplex resource listed on RepeaterBook because I am a moderator. If you are interested in getting your NODE listed there, become a moderator yourself. It's easy work. Help is always welcome. OH ... and the Android and IOS app for RepeaterBook is GREAT for the traveling ham who is as averse to paper as I. :) 2. As an AllstarLink user, I have achieved a number of pleasant QSOs on my computer and phone. I like AllstarLink because it works on any phone, including landline. Conversely, I have been offended by AllstarLink users who were just as welcoming as some on Echolink and IRLP groups. In fact, one trustee of a popular linked system told me publicly, over his system broadcasting RF to all and streaming over the AllstarLink system, that my laptop connection was not welcome. I was happy to tell him that I was disconnecting. I sent him a nice email challenging his QRZ.com profile verbiage about welcome connections and offered to meet him for coffee sometime. I'm still waiting. ... and this is an example of how a fairly new user was treated. In other words, there was no clear lines regarding allowed use. As a result, I am cautious to to connect to some repeaters because they don't reveal their network connections. Nevertheless, amateur radio is a BIG hobby. You are welcome to your corner of it while I occupy mine. :) I will smile at you in person and by email. :) 3. The American Radio Relay League is the biggest US ship sailing the Amateur Radio Sea. The Radio Society of Great Britain and Radio Amateurs of Canada offer similar services in their countries. The ARRL has been a strong proponent of new technology, ex. article on Page 92 of November 2013 QST addressing remote base, i.e. remotehams.com use for DXCC operations, use of Echolink to send Morse Code practice http://www.arrl.org/echolink-irlp so those without HF stations can still participate, etc. If you are not a LEAGUE member, you are letting the membership set the direction of amateur radio for you. I feel the ARRL membership is worth the attorney at the Washington, DC office and the radio insurance that covers my cellphone because, after all, it IS a "radio device" that I can use to talk to people on AllstarLink, Echolink, APRS, and IRLP. If there's something the League is not doing right, I have the ear of the Section Manager and the Division director. I know an email to either does not go to spam. I am a regular participant in the Section Leadership conference call. I hope to connect to you on the local node WX5ASA-R on Echolink and IRLP 8115 with AllStarLink being added as I have time, money, and patience, not necessarily in that order. Otherwise, please find me on remotehams.comenjoying HF operation, scanning local repeaters, and enjoying the social aspects of amateur radio, without degrading comments, over coffee. Oh ... and who wants to help me write the QST article about AllstarLink? 73 -- Lloyd Colston KC5FM Altus, OK USA http://wx5em.us Straight Key Century Club #5676 Croatian Telegraphy Club CTC # 1.931 CARF #294 Ten-Ten #10231 OMISS #8719 Southcars #8276 QCWA #31935 ARRL #8037325 http://www.carf.net http://www.ten-ten.org http://norcars.net/ http://kc5fm.blogspot.com http://doodle.com/kc5fm

4 3

Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 28
by Bradley Haney 12 Oct '13

12 Oct '13

IL Repeater Association will list ALL-STAR NODES :) on the website On Fri, Oct 11, 2013 at 1:54 PM, <app_rpt-users-request(a)ohnosec.org> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. Re: App_rpt-users Digest, Vol 56, Issue 20 (Bryan D. Boyle) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Fri, 11 Oct 2013 14:54:13 -0400 > From: "Bryan D. Boyle" <bdboyle(a)bdboyle.com> > To: app_rpt-users(a)ohnosec.org > Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > Message-ID: <D225A0BA-1F24-4F17-A8B0-7219BAF9C2F5(a)bdboyle.com> > Content-Type: text/plain; charset="us-ascii" > > and if you bridge allstar (superior and more flexible) to IRLP (old 1990s > technology held together with patches and gyrations), Mr Cameron will get > his shorts in a wad and cancel your credentials (but leave you listed as an > active node to hide the fact that his numbers of real nodes is less than it > was...). > > yeah, it still has some mindshare (especially amongst the dinosaurs in the > ARRL, who refuse to acknowledge that allstar exists...and despite the > population of a* approaching that of the older stuff, have refused to list > our nodes as such in the repeater directory...), but progress waits for no > man. > > -- > Bryan > Sent from my iPad > > > On Oct 11, 2013, at 1:47 PM, Johnny Keeker <cypresstower(a)yahoo.com> > wrote: > > > > Plug in your URI, RIM, or usb sound device and you will see it pop up on > the linux screen > > as [root@~] radio-tune-menu > > the radio tune menu will allow you to setup your sound devices provided > your .conf files are correct > > ACID is a repeater controller if you have 2 URIs or RIMs you can bridge > your IRLP node > > beside IRLP configured on an ACID install had some audio level issues. > Not sure about > > Xipar but it also had configs for IRLP. I only tested it on ACID > > p.s. Scott I noticed you seen the publicizing for the RIM > > JK > > > > From: Richard Szajkowski <va3rzs(a)gmail.com> > > To: Johnny Keeker <cypresstower(a)yahoo.com> > > Cc: App_rpt Users <app_rpt-users(a)ohnosec.org> > > Sent: Friday, October 11, 2013 1:06 PM > > Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > > > > How will I know if it works after I plug it in ? Is there a script that > I need to run it install it > > > > I am finding the docs out of date or not there at all (some links are > dead like for the 4 port card) > > > > I know IRLP is not supported any more , sad as I run an IRLP node , and > would have liked to run all 3 networks on one computer , to save a port for > the 220 repeater > > > > I thank you for all your help , > > > > Richard Szajkowski > > > > > >> On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower(a)yahoo.com> > wrote: > >> > >> I don't know the device but if it has a CM108 or CM119 chip it will. > >> Personally, I use startech sound fobs. They're easily modifiable > >> using surface mount components and they're reliable. URI's are very > >> good, but have my eye on the RIM as it has advantages over the URI. > >> JK > >> From: Richard Szajkowski <va3rzs(a)gmail.com> > >> To: Johnny Keeker <cypresstower(a)yahoo.com> > >> Sent: Friday, October 11, 2013 11:42 AM > >> Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > >> > >> Do you know if the signal link USB sound card would work ???? I have > ordered a uri , but I was asked if I would host a node for another repeater > >> > >> Richard Szajkowski > >> > >> > >>> On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> > wrote: > >>> > >>> At the least you have success. It takes about 10 minutes or less, > when you first boot > >>> before your node reports to all the other on-line nodes. Some of my > nodes > >>> use a static IP and others DHCP with reserved address. Let us all > know how things > >>> work out for you. > >>> Good luck Richard > >>> JK > >>> > >>> From: Richard Szajkowski <va3rzs(a)gmail.com> > >>> To: Johnny Keeker <cypresstower(a)yahoo.com> > >>> Sent: Thursday, October 10, 2013 7:02 PM > >>> Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > >>> > >>> I now have what I think is a working system , > >>> > >>> For some reason it fails if I put in a static IP , but if I run with > DHCP it finds the mic and runs > >>> > >>> If I tell it to pull down the info from the server for he node it dies > >>> > >>> I need it on a static IP for port fowarding , just like my other VoIP > systems > >>> > >>> And I did do the info on the web portal to the best I can, I entered > in all the info it requested > >>> > >>> I even got to install your device now , this will be here Tuesday > because of our long weekend > >>> > >>> Thanks for all the help > >>> > >>> Richard Szajkowski > >>> > >>> > >>>> On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> > wrote: > >>>> > >>>> did you Not Create an installation disk???? > >>>> I thought you were past that point and sitting at the test prompt > >>>> If you completed the ACID install and got the test prompt > >>>> the password is 'setup' > >>>> once your in root type passwd and change it > >>>> nodesetup.sh will run the script to push your node config files > from the allstar server to > >>>> your node "provided you created and saved the files prior to your > ACID installation" > >>>> JK > >>>> > >>>> > >>>> > >>>> From: "zeppelin.1(a)netzero.com" <zeppelin.1(a)netzero.com> > >>>> To: app_rpt-users(a)ohnosec.org > >>>> Sent: Thursday, October 10, 2013 5:20 PM > >>>> Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > >>>> > >>>> Hello Richard and welcome to the Linux world; > >>>> You > "must" do a CD BURN to the ISO for it to work properly, low speed is best > for older CD ROM. > >>>> 73 Anton/ KC2RQR > >>>> Node 29103 > >>>> > >>>> ---------- Original Message ---------- > >>>> From: app_rpt-users-request(a)ohnosec.org > >>>> To: app_rpt-users(a)ohnosec.org > >>>> Subject: App_rpt-users Digest, Vol 56, Issue 20 > >>>> Date: Thu, 10 Oct 2013 12:00:01 -0400 > >>>> > >>>> Send App_rpt-users mailing list submissions to > >>>> app_rpt-users(a)ohnosec.org > >>>> > >>>> To subscribe or unsubscribe via the World Wide Web, visit > >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >>>> or, via email, send a message with subject or body 'help' to > >>>> app_rpt-users-request(a)ohnosec.org > >>>> > >>>> You can reach the person managing the list at > >>>> app_rpt-users-owner(a)ohnosec.org > >>>> > >>>> When replying, please edit your Subject line so it is more specific > >>>> than "Re: Contents of App_rpt-users digest..." > >>>> > >>>> > >>>> Today's Topics: > >>>> > >>>> 1. Help with new install (Richard Szajkowski) > >>>> > >>>> > >>>> ---------------------------------------------------------------------- > >>>> > >>>> Message: 1 > >>>> Date: Wed, 9 Oct 2013 18:14:55 -0400 > >>>> From: Richard Szajkowski <va3rzs(a)gmail.com> > >>>> To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > >>>> Subject: [App_rpt-users] Help with new install > >>>> Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D(a)gmail.com> > >>>> Content-Type: text/plain; charset=us-ascii > >>>> > >>>> Hello to the group > >>>> > >>>> I am trying to get the computer on line while my interface is shipped > >>>> > >>>> I downloaded the ISO off the website , followed the prompts , I am > not at a prompt > >>>> Test > > >>>> > >>>> I did not enter a root password as I was not asked > >>>> > >>>> I can't find a PDF or anything on 1st time installs > >>>> > >>>> Any help would be great > >>>> > >>>> Thanks > >>>> > >>>> Richard Szajkowski va3rzs > >>>> > >>>> > >>>> > >>>> ------------------------------ > >>>> > >>>> _______________________________________________ > >>>> App_rpt-users mailing list > >>>> App_rpt-users(a)ohnosec.org > >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >>>> > >>>> > >>>> End of App_rpt-users Digest, Vol 56, Issue 20 > >>>> ********************************************* > >>>> ____________________________________________________________ > >>>> NetZero now offers 4G mobile broadband. Sign up now. > >>>> > >>>> _______________________________________________ > >>>> App_rpt-users mailing list > >>>> App_rpt-users(a)ohnosec.org > >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >>>> _______________________________________________ > >>>> App_rpt-users mailing list > >>>> App_rpt-users(a)ohnosec.org > >>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >

3 2

Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
by Johnny Keeker 11 Oct '13

11 Oct '13

you ll need 2 allstar nodes on one server. once you have your irlp node attached to one of those nodes, you call the "irlp, allstar node" and place it in command mode. with a few rpt.conf changes the dtmf will be able to dial out on irlp. when you actually get the hardware setup, drop a note on this site. myself or other Allstarians will be glad to help out. ACID is as powerful as any hardware repeater controller Ive ever owned, cat, scom, linksys, etc JK From: Richard Szajkowski <va3rzs(a)gmail.com> To: Johnny Keeker <cypresstower(a)yahoo.com> Sent: Friday, October 11, 2013 3:25 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 Not upset , just making a point , and I am talking about Dave C , All I did was buy his card , yes I did make a donation just like I have with DMR and I will with allstar once it's up and running , I believe in supporting systems I use Please don't get me wrong your help and others have got me , what I believe is ready to install the interface if the powers that be had a interface to buy I am sure I would buy that one , witch would help support the project This system has a lot to offer and a lot to learn , I will have to learn so I can teach the users Again thank you for your help Now the next question once we are running is how to unlink the IRLP port from the controller with allstar is up , and discont the allstar port when IRLP is up, I am sure it's going to be a simple script for both But for testing IRLP will just be closed so there is no problems with either network Richard Szajkowski On Oct 11, 2013, at 3:06 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: I didnt want to start a brag list, just trying to help do what I can. >also dont want to patronize anyone, but there is a mindset on irlp, and like you, >I still have a few irlp nodes. far as support for allstar, is right here >one other difference, no one asks you for your $$$support, IRLP you pay up front....... >sorry your not happy so ill quit the correspondence, hope your not offended. >by the way, what Dave are you referring to???? 'you dont have to answer' >JK > >From: Richard Szajkowski <va3rzs(a)gmail.com> >To: Johnny Keeker <cypresstower(a)yahoo.com> >Sent: Friday, October 11, 2013 2:39 PM >Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > > > >I have been with IRLP from almost the start , I have had no problem with Dave or any of the crew > > >I agree with radio to radio system , there are pros and cons > > >I would not put echo link on my repeater because of the computer interface for a long time , it's sorta there now , have to put it back on line > > >I also run a mototrbo system (DMR ) > > >We need allstar because of the RF link system has gone by the waste side ( was told the owner of the hardware has no interest in keeping the network up any more ) so a number of nets like canwarn has moved to allstar , we need to be connected in one form or another > > >Support for IRLP is GREAT , support for DMR is GREAT, support for Echolink is good , > > >Support for allstar , lacking in a lot of spots I would have tossed it if it was not for a couple good people on this mailing list > > >My point being the website is out of date , links are dead and point to sites for sale >And really hard to find info, If I m wrong in my views ok, > > >I find the portal GREAT !!!!!!!!!!!!! I just wish there was a read me for it so that when you get lost you have something to read and figure out what the heck you did > > >I really believe all the VoIP systems have there pros and cons , I don't like d star and will never install a node , no real need to spend that kind of money , there is a node in the area and it does not get a great amount of use , so why bother > > >The pro I can see for this system is I will provide access to my repeater , and if the club in the city wants a node I will do it for them as they don't have net access, and it's a short hop from my repeater site to there's , so no problem for me , I will even by the extra interface and use one of my spare radios to link to them > > >This is a learning curve for me but happy to do it, and help a fellow club > > >Btw our group has 2 members , we cover all costs our self , and ask nothing from anyone >We run a total of 6 repeaters in different modes and freq. > > >So I thank every one for there help in getting the 1st node up and running then move to the 2nd node > > > > > >Richard Szajkowski > > > >On Oct 11, 2013, at 2:10 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: > > >instead of connecting a radio to your usb sound device connect it to your irlp node >>> >>should have mentioned, allstar is far superior to irlp and there is no allstar natzi out there YET >>if you like allstar as much as I do, there is an orange button on the allstarlink.org site "ding ding" >> >>I dont know any of the software guys, I just appreciate what they have created >>(note) the above statements are my personal beliefs >> >> >>From: Richard Szajkowski <va3rzs(a)gmail.com> >>To: Johnny Keeker <cypresstower(a)yahoo.com> >>Sent: Friday, October 11, 2013 1:55 PM >>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >> >> >> >>So IRLP is now allowed ?? How do I set up ? This would allow me 1computerin the shack and one link port , ummmmm >> >>Richard Szajkowski >> >> >> >>On Oct 11, 2013, at 1:47 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: >> >> >>Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen >>>as [root@~] radio-tune-menu >>>the radio tune menu will allow you to setup your sound devices provided your .conf files are correct >>>ACID is a repeater controller if you have 2 URIs or RIMs you can bridge your IRLP node >>>beside IRLP configured on an ACID install had some audio level issues. Not sure about >>>Xipar but it also had configs for IRLP. I only tested it on ACID >>>p.s. Scott I noticed you seen the publicizing for the RIM >>>JK >>> >>> >>>From: Richard Szajkowski <va3rzs(a)gmail.com> >>>To: Johnny Keeker <cypresstower(a)yahoo.com> >>>Cc: App_rpt Users <app_rpt-users(a)ohnosec.org> >>>Sent: Friday, October 11, 2013 1:06 PM >>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >>> >>> >>> >>>How will I know if it works after I plug it in ? Is there a script that I need to run it install it >>> >>> >>>I am finding the docs out of date or not there at all (some links are dead like for the 4 port card) >>> >>> >>>I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater >>> >>> >>>I thank you for all your help , >>> >>>Richard Szajkowski >>> >>> >>> >>>On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: >>> >>> >>>I don't know the device but if it has a CM108 or CM119 chip it will. >>>>Personally, I use startech sound fobs. They're easily modifiable >>>>using surface mount components and they're reliable. URI's are very >>>>good, but have my eye on the RIM as it has advantages over the URI. >>>>JK >>>> >>>>From: Richard Szajkowski <va3rzs(a)gmail.com> >>>>To: Johnny Keeker <cypresstower(a)yahoo.com> >>>>Sent: Friday, October 11, 2013 11:42 AM >>>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >>>> >>>> >>>> >>>>Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater >>>> >>>>Richard Szajkowski >>>> >>>> >>>> >>>>On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: >>>> >>>> >>>>At the least you have success. It takes about 10 minutes or less, when you first boot >>>>>before your node reports to all the other on-line nodes. Some of my nodes >>>>>use a static IP and others DHCP with reserved address. Let us all know how things >>>>>work out for you. >>>>>Good luck Richard >>>>>JK >>>>> >>>>> >>>>>From: Richard Szajkowski <va3rzs(a)gmail.com> >>>>>To: Johnny Keeker <cypresstower(a)yahoo.com> >>>>>Sent: Thursday, October 10, 2013 7:02 PM >>>>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >>>>> >>>>> >>>>> >>>>>I now have what I think is a working system , >>>>> >>>>> >>>>>For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs >>>>> >>>>> >>>>>If I tell it to pull down the info from the server for he node it dies >>>>> >>>>> >>>>>I need it on a static IP for port fowarding , just like my other VoIP systems >>>>> >>>>> >>>>>And I did do the info on the web portal to the best I can, I entered in all the info it requested >>>>> >>>>> >>>>>I even got to install your device now , this will be here Tuesday because of our long weekend >>>>> >>>>> >>>>>Thanks for all the help >>>>> >>>>>Richard Szajkowski >>>>> >>>>> >>>>> >>>>>On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: >>>>> >>>>> >>>>>did you Not Create an installation disk???? >>>>>>I thought you were past that point and sitting at the test prompt >>>>>>If you completed the ACID install and got the test prompt >>>>>>the password is 'setup' >>>>>>once your in root type passwd and change it >>>>>>nodesetup.sh will run the script to push your node config files from the allstar server to >>>>>>your node "provided you created and saved the files prior to your ACID installation" >>>>>>JK >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>>From: "zeppelin.1(a)netzero.com" <zeppelin.1(a)netzero.com> >>>>>>To: app_rpt-users(a)ohnosec.org >>>>>>Sent: Thursday, October 10, 2013 5:20 PM >>>>>>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >>>>>> >>>>>> >>>>>> >>>>>>Hello Richard and welcome to the Linux world; >>>>>> You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. >>>>>>73 Anton/ KC2RQR >>>>>>Node 29103 >>>>>> >>>>>>---------- Original Message ---------- >>>>>>From: app_rpt-users-request(a)ohnosec.org >>>>>>To: app_rpt-users(a)ohnosec.org >>>>>>Subject: App_rpt-users Digest, Vol 56, Issue 20 >>>>>>Date: Thu, 10 Oct 2013 12:00:01 -0400 >>>>>> >>>>>>Send App_rpt-users mailing list submissions to >>>>>>app_rpt-users(a)ohnosec.org >>>>>> >>>>>>To subscribe or unsubscribe via the World Wide Web, visit >>>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>or, via email, send a message with subject or body 'help' to >>>>>>app_rpt-users-request(a)ohnosec.org >>>>>> >>>>>>You can reach the person managing the list at >>>>>>app_rpt-users-owner(a)ohnosec.org >>>>>> >>>>>>When replying, please edit your Subject line so it is more specific >>>>>>than "Re: Contents of App_rpt-users digest..." >>>>>> >>>>>> >>>>>>Today's Topics: >>>>>> >>>>>> 1. Help with new install (Richard Szajkowski) >>>>>> >>>>>> >>>>>>---------------------------------------------------------------------- >>>>>> >>>>>>Message: 1 >>>>>>Date: Wed, 9 Oct 2013 18:14:55 -0400 >>>>>>From: Richard Szajkowski <va3rzs(a)gmail.com> >>>>>>To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> >>>>>>Subject: [App_rpt-users] Help with new install >>>>>>Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D(a)gmail.com> >>>>>>Content-Type: text/plain; charset=us-ascii >>>>>> >>>>>>Hello to the group >>>>>> >>>>>>I am trying to get the computer on line while my interface is shipped >>>>>> >>>>>>I downloaded the ISO off the website , followed the prompts , I am not at a prompt >>>>>>Test > >>>>>> >>>>>>I did not enter a root password as I was not asked >>>>>> >>>>>>I can't find a PDF or anything on 1st time installs >>>>>> >>>>>>Any help would be great >>>>>> >>>>>>Thanks >>>>>> >>>>>>Richard Szajkowski va3rzs >>>>>> >>>>>> >>>>>> >>>>>>------------------------------ >>>>>> >>>>>>_______________________________________________ >>>>>>App_rpt-users mailing list >>>>>>App_rpt-users(a)ohnosec.org >>>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> >>>>>>End of App_rpt-users Digest, Vol 56, Issue 20 >>>>>>********************************************* >>>>>> >>>>>>____________________________________________________________ >>>>>>NetZero now offers 4G mobile broadband. Sign up now. >>>>>>_______________________________________________ >>>>>>App_rpt-users mailing list >>>>>>App_rpt-users(a)ohnosec.org >>>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> >>>>>> >>>>>_______________________________________________ >>>>>>App_rpt-users mailing list >>>>>>App_rpt-users(a)ohnosec.org >>>>>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>> >>>>> >>>> >>>> >>> >>> >> >> > >

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
by Johnny Keeker 11 Oct '13

11 Oct '13

I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK From: Richard Szajkowski <va3rzs(a)gmail.com> To: Johnny Keeker <cypresstower(a)yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater Richard Szajkowski On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: At the least you have success. It takes about 10 minutes or less, when you first boot >before your node reports to all the other on-line nodes. Some of my nodes >use a static IP and others DHCP with reserved address. Let us all know how things >work out for you. >Good luck Richard >JK > > >From: Richard Szajkowski <va3rzs(a)gmail.com> >To: Johnny Keeker <cypresstower(a)yahoo.com> >Sent: Thursday, October 10, 2013 7:02 PM >Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 > > > >I now have what I think is a working system , > > >For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs > > >If I tell it to pull down the info from the server for he node it dies > > >I need it on a static IP for port fowarding , just like my other VoIP systems > > >And I did do the info on the web portal to the best I can, I entered in all the info it requested > > >I even got to install your device now , this will be here Tuesday because of our long weekend > > >Thanks for all the help > >Richard Szajkowski > > > >On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower(a)yahoo.com> wrote: > > >did you Not Create an installation disk???? >>I thought you were past that point and sitting at the test prompt >>If you completed the ACID install and got the test prompt >>the password is 'setup' >>once your in root type passwd and change it >>nodesetup.sh will run the script to push your node config files from the allstar server to >>your node "provided you created and saved the files prior to your ACID installation" >>JK >> >> >> >> >> >> >>From: "zeppelin.1(a)netzero.com" <zeppelin.1(a)netzero.com> >>To: app_rpt-users(a)ohnosec.org >>Sent: Thursday, October 10, 2013 5:20 PM >>Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 >> >> >> >>Hello Richard and welcome to the Linux world; >> You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. >>73 Anton/ KC2RQR >>Node 29103 >> >>---------- Original Message ---------- >>From: app_rpt-users-request(a)ohnosec.org >>To: app_rpt-users(a)ohnosec.org >>Subject: App_rpt-users Digest, Vol 56, Issue 20 >>Date: Thu, 10 Oct 2013 12:00:01 -0400 >> >>Send App_rpt-users mailing list submissions to >>app_rpt-users(a)ohnosec.org >> >>To subscribe or unsubscribe via the World Wide Web, visit >>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>or, via email, send a message with subject or body 'help' to >>app_rpt-users-request(a)ohnosec.org >> >>You can reach the person managing the list at >>app_rpt-users-owner(a)ohnosec.org >> >>When replying, please edit your Subject line so it is more specific >>than "Re: Contents of App_rpt-users digest..." >> >> >>Today's Topics: >> >> 1. Help with new install (Richard Szajkowski) >> >> >>---------------------------------------------------------------------- >> >>Message: 1 >>Date: Wed, 9 Oct 2013 18:14:55 -0400 >>From: Richard Szajkowski <va3rzs(a)gmail.com> >>To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> >>Subject: [App_rpt-users] Help with new install >>Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D(a)gmail.com> >>Content-Type: text/plain; charset=us-ascii >> >>Hello to the group >> >>I am trying to get the computer on line while my interface is shipped >> >>I downloaded the ISO off the website , followed the prompts , I am not at a prompt >>Test > >> >>I did not enter a root password as I was not asked >> >>I can't find a PDF or anything on 1st time installs >> >>Any help would be great >> >>Thanks >> >>Richard Szajkowski va3rzs >> >> >> >>------------------------------ >> >>_______________________________________________ >>App_rpt-users mailing list >>App_rpt-users(a)ohnosec.org >>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> >>End of App_rpt-users Digest, Vol 56, Issue 20 >>********************************************* >>____________________________________________________________ >>NetZero now offers 4G mobile broadband. Sign up now. >>_______________________________________________ >>App_rpt-users mailing list >>App_rpt-users(a)ohnosec.org >>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> >> >_______________________________________________ >>App_rpt-users mailing list >>App_rpt-users(a)ohnosec.org >>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> > >

5 6