September 2015 - App_rpt-users

Re: [App_rpt-users] ACID (Centos 6.7)
by kk6ecm 09 Sep '15

09 Sep '15

P.S. I used a scope on the URIx with this board before, which is how I initially discovered I could not get the audio to work. -----Original Message----- From: kk6ecm [mailto:kk6ecm@gmail.com] Sent: Wednesday, September 09, 2015 4:45 PM To: 'mike(a)midnighteng.com'; 'app_rpt-users(a)ohnosec.org' Subject: RE: [App_rpt-users] ACID (Centos 6.7) Board - Gigabyte Intel NM70 Chipset HDMI SATA 6Gbps Mini ITX DDR3 1600 Intel Motherboards GA-C1007UN-D I was never able to get either ACID CentOS 5.10 or 6.7 to work with this board. The audio did not work. I used uridiag to test the audio at that time. The digital portion passed, but not the audio. I've not loaded uridiag onto th3 ACID CentOS 6.7 build to see if it works. On 8-17-2015 I burned a CD using acid_centos6 downloaded 9/23/2014 Used the CD to perform a fresh install from a USB CDROM drive, following the on-screen instructions on 8-17-2015, then left it because I ran out of time. Today I booted it back up, connected to internet and the URIx. Then performed a 'yum update' at the command line Then fixed Zaptel after the yum update in accordance with http://docs.allstarlink.org/drupal/node/111 Then hooked up the amplified speaker to the URIx as a baseline test to confirm the audio still did not work, and IT DID! Audio is clear. At least that is what my notes say. I don't remember doing anything else. Hope this helps, Bob kk6ecm -----Original Message----- From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of mike(a)midnighteng.com Sent: Wednesday, September 09, 2015 4:16 PM To: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] ACID (Centos 6.7) Could you say what the chipset and/or board is you installed 0n ? And did you upgrade the kernal and software ot a fresh install ? ...mike/kb8jnm > What I'm saying is, it's working. I'm running the URIx, with audio out. > I've not checked the total interface, but the audio that did not work > before is working now after a him update and the follow-Zapata repair per > the allstarlink instructions. Is it possible something got "fixed" with > the Tim update? What do I need to do the make sure it is fully functional > besides integrating it with a repeater, which I may have time to do this > weekend. > > Thanks, > Bob > kk6ecm > > Sent from iPad > > >> On Sep 9, 2015, at 3:39 PM, Jim Duuuude <telesistant(a)hotmail.com> wrote: >> >> The USB and/or audio stuff in Centos 6 is broken. >> >> That is why we have never released a Centos 6 based version >> of ACID. >> >> > From: kk6ecm(a)gmail.com >> > To: app_rpt-users(a)ohnosec.org >> > Date: Wed, 9 Sep 2015 15:20:31 -0700 >> > Subject: [App_rpt-users] ACID (Centos 6.7) >> > >> > I decided to try to work on ACID (CentOS 6.7) after several failed >> attempts >> > in the past. I loaded up the CD, did a yum update, then fixed zapata. >> I have >> > it running now. It seems to work fine with the URIx, and I can connect >> to >> > other Allstar nodes. I have the URIx connected to an amplified >> speaker, and >> > the audio comes through fine. I am using iaxRPT with it. When I tried >> to get >> > it working before, I could not get any of the audio functions working. >> The >> > interesting part is I'm running in on a mini-ITX with a newer chipset >> that I >> > could never get to work with the current (CentOS 5.10) ACID release. >> The >> > digital (i.e. PTT) worked fine, but none of the audio pieces. >> > >> > Am I missing something? I'm using the acid_centos6.iso file from >> 9/23/2014. >> > >> > Thanks, >> > Bob >> > kk6ecm >> > >> > _______________________________________________ >> > App_rpt-users mailing list >> > App_rpt-users(a)ohnosec.org >> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> > >> > To unsubscribe from this list please visit >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >> down to the bottom of the page. Enter your email address and press the >> "Unsubscribe or edit options button" >> > You do not need a password to unsubscribe, you can do it via email >> confirmation. If you have trouble unsubscribing, please send a message >> to the list detailing the problem. > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] New Acid install - kickstart download fail from USB
by Larry da Ponte 09 Sep '15

09 Sep '15

Thanks Loren, I tried this method you suggested but the thumb drive does not show up as a bootable device now, I'm thinking it may be because the PC I'm installing on uses EUFI, not a bios. I'll see if there is a comparability mode but I don't think so. -Larry On Tue, Sep 8, 2015 at 6:56 AM -0700, "Loren Tedford" <lorentedford(a)gmail.com> wrote: Sorry for the short responses earlier i was still mobile with the phone all morning.. Here is kinda what i do but I usually do lsusb to see what the devices are..Below an example of lsusb outputloren@loren-Laptop:~$ lsusbBus 002 Device 003: ID 1c4f:0002 SiGma Micro Keyboard TRACER Gamma IvoryBus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching HubBus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubBus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hubBus 003 Device 003: ID 093a:2510 Pixart Imaging, Inc. Optical MouseBus 003 Device 002: ID 046d:0a37 Logitech, Inc. Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubBus 001 Device 004: ID 1bcf:2880 Sunplus Innovation Technology Inc. Bus 001 Device 003: ID 8086:0189 Intel Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching HubBus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubloren@loren-Laptop:~$ loren@loren-Laptop:~$ df -hFilesystem Size Used Avail Use% Mounted on/dev/sda4 572G 108G 435G 20% /none 4.0K 0 4.0K 0% /sys/fs/cgroupudev 3.9G 4.0K 3.9G 1% /devtmpfs 790M 1.4M 788M 1% /runnone 5.0M 0 5.0M 0% /run/locknone 3.9G 35M 3.9G 1% /run/shmnone 100M 40K 100M 1% /run/user I no longer use Windows at all I use Xubuntu Studio 14.04 LTS Windows kinda made me a little mad so i made the switch.. I hope some of this helps you out with the install if not let me know it could be the iso imagine you have might be corrupt i dont like to think of that but it is possible.. http://askubuntu.com/questions/59551/how-to-burn-a-windows-iso-to-a-usb-dev… Insert the USB device and then open Disk Utility (in 10.10 and older, System -> Administration -> Disk Utility).Select the USB device from the list in the left of the program and detect where it was mounted: /dev/sd[1 letter][optionally 1 number]. For example, /dev/sdc or /dev/sdc1. Make sure the USB device is unmounted (not safely removed, but unmounted) If it is mounted you can unmount it:sudo umount /dev/sd[1 letter][optionally 1 number] Assuming the .iso file is in your home folder, open the terminal and write:sudo dd bs=4M if=[ur .iso] of=/dev/sd[that 1 letter] Example:sudo dd bs=4M if=windows7.iso of=/dev/sdc And wait for it to finish. (The "bs=4M" - bit is optional, just makes it faster.) Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.comPhone: 618-553-0806http://www.lorentedford.com http://www.kc9zhv.comhttp://hub.kc9zhv.com On Tue, Sep 8, 2015 at 8:25 AM, Larry da Ponte <hb9eyq(a)gmail.com> wrote: That's encouraging, what method do you use to create your USB stick installs? Combination of fdisk, dd, and file copying? -Larry _____________________________ From: Loren Tedford <lorentedford(a)gmail.com> Sent: Dienstag, September 8, 2015 1:55 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Larry da Ponte <hb9eyq(a)gmail.com> Generally all my installations I use a usb stick.. However I use Linux based computer with a terminal or command prompt as the windows users would say Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 6:39 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: Thanks Loren. This is interesting, looking over the site I see it's for creating live Linux installs that run from a USB stick, I'm trying to create installation media on a USB stick that will install to an SSD in the PC. Once the installation is complete, I would no longer need the USB stick. -Larry _____________________________ From: Loren Tedford < lorentedford(a)gmail.com> Sent: Dienstag, September 8, 2015 1:18 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Larry da Ponte < hb9eyq(a)gmail.com> I'm not sure with Windows you might try this http://unetbootin.github.io Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 5:44 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: I used the windows Rufus app to create the bootable USB stick from the acid_centos.iso. I'm thinking this may be the trouble. I will probably need to find another method for creating the USB stick. Recommendations for a procedure that has worked for the Acid ISO? Thanks -Larry _____________________________ From: Larry da Ponte < hb9eyq(a)gmail.com> Sent: Dienstag, September 8, 2015 12:26 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Loren Tedford < lorentedford(a)gmail.com>, < app_rpt-users(a)ohnosec.org> Thanks for the reply Loren. The same iso file installs without error when installed on a new VM. Have you had success with a USB thumb drive install? Perhaps Acid install from USB is not supported. -Larry On Tue, Sep 8, 2015 at 2:46 AM -0700, "Loren Tedford" <lorentedford(a)gmail.com> wrote: I know it sounds far fetched but it almost sounds like a corrupt ISO image.. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 1:54 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: First time AllStar user and node setup. I have a small form factor PC with no CD ROM or floppy. I've created a Acid Centos install on a USB stick but after it successfully boots from the stick and status the install it complains it can't find the kickstart file and then prompts me for cdrom. I've confirmed the ks.cfg is in /Dev/sdb1:/ks.cfg but even with kickstart boot options it fails to find it. Same PC installs Centos 7 from same USB stick without issue. I've used the Centos Wiki page To create a USB stick install using the Centos-5 section but this method rests in a USB key that is not recognized by eufi as bootable. I'm using an acid_centos.iso downloaded a couple of days ago from the AllStar home page. I have not tried putting the ks.cfg on an FTP or web server yet - anyone have success with Acid install from stick? I also burned the ISO to a CD and booted from a USB CD ROM drive but it also fails to "download" the kickstart - exact experience as USB key. Have tried all three of the USB ports on this PC. Have also tried two different USB sticks. 73 -Larry _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Uri for echo link
by Skyler Fennell 09 Sep '15

09 Sep '15

Might be off topic but Is the USB radio interface by DMK supported with the PC echo link client? Have a friend who wants to setup the PC echo link and had only usb. I'm trying to convince him to just do Allstar with echo link but I am curious if it works using the PC client.

4 4

How low can you go?!
by Buddy Brannan 09 Sep '15

09 Sep '15

Yet another single board computer. Wonder how app_rpt and friends will run on it? Maybe I'll have to get one. Just how cheap can we put together a portable node? http://www.techworm.net/2015/09/single-board-orange-pi-pc-mini-computer-lau… -- Buddy Brannan, KB5ELV - Erie, PA Phone: 814-860-3194 Mobile: 814-431-0962 Email: buddy(a)brannan.name

1 0

re stat page having problems?
by REDBUTTON_CTRL 09 Sep '15

09 Sep '15

Seems the Allstar stat page is having problems showing recent nodes. Anyone else notice this? My nodes are reporting fine but some dont show up on the stats page. Jon VA3RQ

1 0

Re: [App_rpt-users] audio problem
by Doug Crompton 08 Sep '15

08 Sep '15

Yes, there is no guarantee that both nodes audio will be in sync. Are you hearing the echo between the two nodes when you are listening to both or when you are just listening to one or the other? It should not matter if they are in sync since no one generally listens to both at the same time right? 73 Doug WA3DSP http://www.crompton.com/hamradio From: mzfb(a)aol.com To: app_rpt-users(a)ohnosec.org Date: Fri, 4 Sep 2015 14:53:10 -0400 Subject: [App_rpt-users] audio problem I have a problem with connecting two Nodes with link radios attached by URI’s. Has anyone experience an audio echo when linking two nodes together? I have reading about the audio delay problems here but it’s not the same. The following is my setup; Running both nodes on an Acid system using one computer. The computer is a Pentium 4 3 Ghz, 1 Gig of Ram 80 gig HDD Both link radios are running on different bands 6 meters and 900mhz. With both connect together I get an audio echo, unlinking it will go away. Both operate just fine when separately to connected to another system but when I connect in the second node to the same system everyone hears an echo from me. I do not have a reverse of that, in that I don’t have an echo when both are connected and I am just receiving. There is no RF problem between the two radio’s. Is there an audio processing delay between the to nodes? Any thoughts or ideas would greatly be appreciated. ThanksMikeW1`ZFB This email has been protected by YAC (Yet Another Cleaner) www.yac.mx _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

2 2

Re: [App_rpt-users] Uri for echo link
by Skyler F 08 Sep '15

08 Sep '15

What do people usually use for PTT on EchoLink? On Tue, Sep 8, 2015 at 11:34 AM, David McGough <kb4fxc(a)inttek.net> wrote: > > No > > On Tue, 8 Sep 2015, Skyler Fennell wrote: > > > Might be off topic but Is the USB radio interface by DMK supported with > the PC echo link client? > > > > Have a friend who wants to setup the PC echo link and had only usb. > > > > I'm trying to convince him to just do Allstar with echo link but I am > curious if it works using the PC client. > > > > > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. > > > > -- Skyler Fennell amsatnet.info KDØWHB electricity440(a)gmail.com

1 0

Re: [App_rpt-users] New Acid install - kickstart download fail from USB
by Larry da Ponte 08 Sep '15

08 Sep '15

That's encouraging, what method do you use to create your USB stick installs? Combination of fdisk, dd, and file copying? -Larry _____________________________ From: Loren Tedford <lorentedford(a)gmail.com> Sent: Dienstag, September 8, 2015 1:55 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Larry da Ponte <hb9eyq(a)gmail.com> Generally all my installations I use a usb stick.. However I use Linux based computer with a terminal or command prompt as the windows users would say Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 6:39 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: Thanks Loren. This is interesting, looking over the site I see it's for creating live Linux installs that run from a USB stick, I'm trying to create installation media on a USB stick that will install to an SSD in the PC. Once the installation is complete, I would no longer need the USB stick. -Larry _____________________________ From: Loren Tedford < lorentedford(a)gmail.com> Sent: Dienstag, September 8, 2015 1:18 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Larry da Ponte < hb9eyq(a)gmail.com> I'm not sure with Windows you might try this http://unetbootin.github.io Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 5:44 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: I used the windows Rufus app to create the bootable USB stick from the acid_centos.iso. I'm thinking this may be the trouble. I will probably need to find another method for creating the USB stick. Recommendations for a procedure that has worked for the Acid ISO? Thanks -Larry _____________________________ From: Larry da Ponte < hb9eyq(a)gmail.com> Sent: Dienstag, September 8, 2015 12:26 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Loren Tedford < lorentedford(a)gmail.com>, < app_rpt-users(a)ohnosec.org> Thanks for the reply Loren. The same iso file installs without error when installed on a new VM. Have you had success with a USB thumb drive install? Perhaps Acid install from USB is not supported. -Larry On Tue, Sep 8, 2015 at 2:46 AM -0700, "Loren Tedford" <lorentedford(a)gmail.com> wrote: I know it sounds far fetched but it almost sounds like a corrupt ISO image.. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 1:54 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: First time AllStar user and node setup. I have a small form factor PC with no CD ROM or floppy. I've created a Acid Centos install on a USB stick but after it successfully boots from the stick and status the install it complains it can't find the kickstart file and then prompts me for cdrom. I've confirmed the ks.cfg is in /Dev/sdb1:/ks.cfg but even with kickstart boot options it fails to find it. Same PC installs Centos 7 from same USB stick without issue. I've used the Centos Wiki page To create a USB stick install using the Centos-5 section but this method rests in a USB key that is not recognized by eufi as bootable. I'm using an acid_centos.iso downloaded a couple of days ago from the AllStar home page. I have not tried putting the ks.cfg on an FTP or web server yet - anyone have success with Acid install from stick? I also burned the ISO to a CD and booted from a USB CD ROM drive but it also fails to "download" the kickstart - exact experience as USB key. Have tried all three of the USB ports on this PC. Have also tried two different USB sticks. 73 -Larry _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

2 1

Re: [App_rpt-users] New Acid install - kickstart download fail from USB
by Larry da Ponte 08 Sep '15

08 Sep '15

Thanks Loren. This is interesting, looking over the site I see it's for creating live Linux installs that run from a USB stick, I'm trying to create installation media on a USB stick that will install to an SSD in the PC. Once the installation is complete, I would no longer need the USB stick. -Larry _____________________________ From: Loren Tedford <lorentedford(a)gmail.com> Sent: Dienstag, September 8, 2015 1:18 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Larry da Ponte <hb9eyq(a)gmail.com> I'm not sure with Windows you might try this http://unetbootin.github.io Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 5:44 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: I used the windows Rufus app to create the bootable USB stick from the acid_centos.iso. I'm thinking this may be the trouble. I will probably need to find another method for creating the USB stick. Recommendations for a procedure that has worked for the Acid ISO? Thanks -Larry _____________________________ From: Larry da Ponte < hb9eyq(a)gmail.com> Sent: Dienstag, September 8, 2015 12:26 nachm. Subject: Re: [App_rpt-users] New Acid install - kickstart download fail from USB To: Loren Tedford < lorentedford(a)gmail.com>, < app_rpt-users(a)ohnosec.org> Thanks for the reply Loren. The same iso file installs without error when installed on a new VM. Have you had success with a USB thumb drive install? Perhaps Acid install from USB is not supported. -Larry On Tue, Sep 8, 2015 at 2:46 AM -0700, "Loren Tedford" <lorentedford(a)gmail.com> wrote: I know it sounds far fetched but it almost sounds like a corrupt ISO image.. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 1:54 AM, "Larry da Ponte" < hb9eyq(a)gmail.com> wrote: First time AllStar user and node setup. I have a small form factor PC with no CD ROM or floppy. I've created a Acid Centos install on a USB stick but after it successfully boots from the stick and status the install it complains it can't find the kickstart file and then prompts me for cdrom. I've confirmed the ks.cfg is in /Dev/sdb1:/ks.cfg but even with kickstart boot options it fails to find it. Same PC installs Centos 7 from same USB stick without issue. I've used the Centos Wiki page To create a USB stick install using the Centos-5 section but this method rests in a USB key that is not recognized by eufi as bootable. I'm using an acid_centos.iso downloaded a couple of days ago from the AllStar home page. I have not tried putting the ks.cfg on an FTP or web server yet - anyone have success with Acid install from stick? I also burned the ISO to a CD and booted from a USB CD ROM drive but it also fails to "download" the kickstart - exact experience as USB key. Have tried all three of the USB ports on this PC. Have also tried two different USB sticks. 73 -Larry _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] New Acid install - kickstart download fail from USB
by Larry da Ponte 08 Sep '15

08 Sep '15

Thanks for the reply Loren. The same iso file installs without error when installed on a new VM. Have you had success with a USB thumb drive install? Perhaps Acid install from USB is not supported. -Larry On Tue, Sep 8, 2015 at 2:46 AM -0700, "Loren Tedford" <lorentedford(a)gmail.com> wrote: I know it sounds far fetched but it almost sounds like a corrupt ISO image.. Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com Sent from Droid RAZR HD from Verizon wireless network On Sep 8, 2015 1:54 AM, "Larry da Ponte" <hb9eyq(a)gmail.com> wrote: First time AllStar user and node setup. I have a small form factor PC with no CD ROM or floppy. I've created a Acid Centos install on a USB stick but after it successfully boots from the stick and status the install it complains it can't find the kickstart file and then prompts me for cdrom. I've confirmed the ks.cfg is in /Dev/sdb1:/ks.cfg but even with kickstart boot options it fails to find it. Same PC installs Centos 7 from same USB stick without issue. I've used the Centos Wiki page To create a USB stick install using the Centos-5 section but this method rests in a USB key that is not recognized by eufi as bootable. I'm using an acid_centos.iso downloaded a couple of days ago from the AllStar home page. I have not tried putting the ks.cfg on an FTP or web server yet - anyone have success with Acid install from stick? I also burned the ISO to a CD and booted from a USB CD ROM drive but it also fails to "download" the kickstart - exact experience as USB key. Have tried all three of the USB ports on this PC. Have also tried two different USB sticks. 73 -Larry _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 1